manualshive.com logo in svg

Hallicrafters SR-2000, Repair Manual, Page: 20 / 27

Share
Download
Hallicrafters SR-2000 Repair Manual Download Page 20

REPAIR AND RESTORATION OF THE SR-2000

 

20 

WDØGOF 3/7/20014 

 

Reinstall V12 and connect the scope to the junction of L20 and CR11, key the transmitter. You should see a 
signal of 4 vpp or more.  
1, If not then C107 or L20 is bad (this is predicated on the fact that all signals in the tests in section 1-5-3 were 
good).  
2, Check the signal voltage across C106 in the transmit mode. There should be little or no loss across the 
capacitor. If there is replace C106.  

 

That completes the testing of the het osc TX switching circuits. Go to section 

3-4-2

 in this document and run the 

driver tests 

5-3 TX 6.5 MHz LOW INJECTION TO 2

ND

 MIXER 

Once again the prerequisite is that the receiver has been debugged and is working at or near spec. If the receiver 
is working properly and the 6.5 IF injection is low then C97 or the wire to C97 is the most likely cause. 

 

5-4 TX DRIVER FAULT 

Verify on all bands, that the proper drive signal is present in section 3-4-2. If the verification is true then V18 or 
its associated circuitry is at fault.  

•

 

Replace the tube. 

•

 

Check the voltages on pins 1, 2, 7 and 8. 

•

 

Check the resistance to gnd on pins 1, 2, 7 and 8. 

•

 

Clean the S1G and S1H.   

Once the fault is cleared return to 3-4-2 verify the driver is functioning properly. 

Summary of Contents for SR-2000




























Reviews:

No comments