manualshive.com logo in svg

Hallicrafters SR-2000, Repair Manual, Page: 15 / 27

Share
Download
Hallicrafters SR-2000 Repair Manual Download Page 15

REPAIR AND RESTORATION OF THE SR-2000

 

15 

WDØGOF 3/7/20014 

3-4-2 Driver output test 

 

The High Voltage will remain off for the following tests. 
Set all controls to the standard setup condition. Power up, warm up 10 minutes. Remove the tube 
shield from V18 and install the capacitive pickup and connect the scope. You will be testing all 
bands. Adjustment of the PRESELECTOR and the driver grid and plate coils will be required for 
each band. The process will be: 
<Select band. 
<Preset PRESELECTOR to proper band segment. 
<Preset main tuning. 
<KEY transmitter. 

<Peak PRESELECTOR. 
<Peak driver grid and plate coils as indicated in chart below. 
<Record peak to peak voltage reading on scope. 
  BAND   MAIN TUNING   GRID COIL   PLATE COIL   VOLTAGE PEAK TO PEAK  

80,             3.900                     L11                   L34                20 vpp         

 

40,             7.23                       L10                   L33                28 vpp         

 

20,           14.28                       L9                     L32                26 vpp       

 

15,           21.36                       L8                     L31                25 vpp       

 

10,           28.75                       L7                     L30                20 vpp        

If any or all bands do not produce the peak to peak voltage noted go to 3-4-3. 

 

3-4-2-1 PA FINAL PRETEST

:  

When all faults have been cleared and the driver output is correct on all bands power down. Go get a cup of 
coffee pick up the manual go to Section V of the manual and read the TUNING PROCEDURE. If necessary 
review the FUNCTIONS OF OPERATING CONTROLS in section IV. Be very sure you understand all the 
processes in the TUNING PROCEDURE. Any misstep from this point on could cost you a set of $1600 final 
tubes. If you are unable to get normal power out you have a fault in the PA sub-circuits. 

VOLTAGES IN THE 

PA SUB-CIRCUITS ARE LETHAL. IF YOU ARE NOT EXPERIENCED IN HIGH VOLTAGE RF 
TROUBLESHOOTING IT IS TIME TO FIND A MENTOR.

 Go to section 5-5 for PA fault isolation.

 

 

NOTE: 18vpp on any band will drive Blue Burle tubes to saturation and the Green Burle tubes will 
require 21vpp to fully saturate. The Black Burle tubes cannot be used in the SR-2000. For in-depth 
discussions on the bias conditions and matching of the 8122 tubes go to 

k9amx.com

 .  

3-4-3 TX second mixer output test 

You have arrived at this point because one or more of the bands failed the tests in 3-4-2. If all bands were dead 
conduct the test on 80 meters. Otherwise go the band that failed in 3-4-2. 
Connect the scope to pin 2 of V18. Key the TX, you should have 6 vpp on pin 2 of V18. Disconnect the scope 
and connect the frequency counter to pin 2 of V18. Key the TX and the counter should display the TX the 
frequency determined by the band selection and the main tuning dial. If it is not there or the wrong frequency 
you may have a fault in the 2

nd

 TX mixer or its associated circuitry. Go to 3-4-4 TX second mixer input test. 

 
Quick review: We got to this point because the initial driver output test failed. Once you establish proper signal 
from the 2

nd

 TX Mixer rerun the test in 3-4-2. If you still do not have proper drive levels you have a fault in the 

Summary of Contents for SR-2000




























Reviews:

No comments