manualshive.com logo in svg

Hallicrafters HT-44, Operation And Maintenance Manual, Page: 12 / 30

Share
Download
Hallicrafters HT-44 Operation And Maintenance Manual Download Page 12

 

12 

 

1-7 FIRST MIXER, 6-6.5MHz I.F., SECOND MIXER 

The first mixer, 6meg IF and second mixer train is composed of V6, T3, V7A, T4 and V8. 

 

1-7-1, MIXER/I.F. SETUP & ALIGNMENT 

Power up in safe mode. Allow 10 minute warm up. 
Locate test points TP 1, TP 2 and TP3. 

1-7-1-1, INJECTION LEVEL PRETEST 

Set RF LEVEL to max. 
Connect microphone. 
Band switch to 7.0. 
Connect the scope to TP1 pin 1 of V6. Key the mic and you should see 0.5vpp (from the carrier oscillator). If 
not Adjust T2 for 0.5vpp. 
Connect the scope to TP2 pin 7 of V6. You should have 0.5vpp constant. (from the VFO). If this signal is not 
present there is a fault in S1 (VFO SELECTOR) or you made an error in the 1-5-3 section tests. Return there 
and correct the fault. 

1-7-1-2, 6MEG ALIGNMENT 

Connect the scope to TP3 pin 2 of V8. Set the VFO to 100 and adjust T3 and T4 top ends for max signal on the 
scope (approx. 1vpp). Tune the VFO to 400 and adjust T3 and T4 bottom ends for 1vpp signal. 
Recheck at 100 and 400 on the dial and retune until both ends are the same you should have 1vpp +/- 0.3vpp. 

MIXER/IF VOLTAGE CHART 

V6 

 

V7 

 

V8 

PIN 

VOLTAGE 

 

PIN 

VOLTAGE 

 

PIN 

VOLTAGE 

1 

0 

 

2 

0 

 

2 

-144/-0.5 

2 

1.0 

*

 

 

3 

83/73 

 

7 

317/276 

5 

317/277 

 

6 

1.1/0.9 

 

8 

158/57 

6 

61/53 

*

 

 

7 

317/274 

 

 

 

7 

0 

 

 

 

 

 

 

Voltages with * will differ dependent upon band selection.  
Measured in MOX, AM, RF LEVEL at max. first voltage 

unkeyed

/second voltage 

keyed

. 

 

 

Summary of Contents for HT-44































Reviews:

No comments