WARNING
Failure to comply with these instructions can cause serious injury and damage to the
vehicle. If you are in any way unsure, do not attempt to use this product and consult
a qualified mechanic
1. Read and understand instruction manuals fully before use. Use only as specified.
2. Never overload this jack by exceeding its rated safe working load.
3. Check vehicle owner’s manual for gross vehicle weight.
4. This jack is for lifting purposes only.
5. Ensure all body parts are kept clear of the jack and vehicle during the raising and lowering
operation.
6. After lifting the vehicle, support immediately with properly rated axle stands.
7. Never work on or under a vehicle without using properly rated axle stands.
8. Only use on solid, even and level ground with the wheels chocked, the vehicle in gear
and its handbrake on.
9. Ensure that the wheels of the jack are rolling freely, all 4 wheels of the jack remain on the
ground during operation.
10. Always ensure that the load is centred on the jack saddle. Off centre loads can become
unstable and slip resulting in possible damage or injury.
11. Only use jacking points specified by your vehicle manufacturer. Some vehicles may require
a manufacturer specific adaptor. Check vehicle handbook for location and details.
12. Ensure vehicle jacking points are in good, sound condition with no corrosion etc.
13. Do not attempt to move or dolly the vehicle whilst on the jack.
14. This jack is not designed to support extensions, cradles etc.
15. Do not attempt to modify this jack in any way.
16. Do not attempt to use this jack if you suspect a fault.
17. Do not start the vehicle in its raised position.
18. Do not attempt to enter the vehicle and ensure all passengers are out of the car when using
this product.
1. Front castor
2. Saddle
3. Handle fork
4. Release valve
5. Handle storage hook
6. Rear castor assembly
7. Jack carry handle
PARTS OF THE JACK
BEFORE FIRST USE
Air may become trapped in the hydraulic system during transit. To purge air:
1. Open the release valve by rotating the handle counter clockwise one full turn.
2. Place the handle in the handle socket and pump about 4 full strokes to purge the air from the
pump and valving.
3. Close the release valve. Pump the handle until the jack has reached full extension. Continue
to pump several times to purge air from under the ram.
4. Open the release valve and push ram into its lowest position. Close the release valve and
operate normally.
Note: If the jack responds immediately to pump action, it is free of air and ready for operation.
If not, repeat procedure.
INSPECTION BEFORE EACH USE
Visual inspection should be made before each use of the jack. Check for leaking hydraulic fluid,
cracked welds and damaged, loose or missing parts.
Any jack which appears to be damaged in any way, found to be badly worn, operates abnormally,
or has been subjected to an abnormal load or shock
MUST NOT BE USED
.
Use Service Jack For
Lifting purposes
ONLY.
Always support
Vehicle with
Jack stands.
OPERATING INSTRUCTIONS
IMPORTANT:
Only use jacking points specified by your vehicle manufacturer. Some vehicles may
require a manufacturer specific adaptor. Check vehicle handbook for location and details.
TO MOVE:
Place handle in operating lever. Do not move the jack when handle is on the release valve as this
may cause damage to the jack. Do not attempt to move the jack whilst under load.
TO LIFT THE VEHICLE:
1. Park the vehicle on solid, even and level ground. Apply the handbrake, place the vehicle
in gear (P if automatic) and chock the wheels that will remain on the ground.
2. Using the jack handle as a wrench, turn the release valve clockwise until fully tightened,
DO NOT OVERTIGHTEN.
3. Place the handle into the operating lever and position the jack under the jacking point of the
vehicle. Pump up and down until the saddle reaches the jacking point. Before lifting, ALWAYS
ensure that the load point is centred on the jack saddle and cannot slip. Off centre loads can
become unstable and slip resulting in damage or injury.
4. Once secure on the jacking point, begin to raise load to desired height by pumping the handle.
IMMEDIATELY support the vehicle by placing properly rated axle stands under a strong, stable
point on the vehicle. Consult the vehicle owner’s manual and axle stand instruction manual for
guidance. DO NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR PLACING OR
REMOVING JACK STANDS!
FOR YOUR SAFETY AND TO PREVENT INJURY:
1
2
3
7
4
6
5
