background image

Page 

3

 

 

 

SmartFOAM 

SAFETY 

 

 

IMPORTANT!

 

 

THE HALE SMARTFOAM MODELS 2.1A  AND 1.7AHP CLASS “A” ELECTRONIC FOAM  PROPORTIONING SYSTEMS 

ARE DESIGNED  FOR OPTIMUM SAFETY OF ITS OPERATORS  AND TO PROVIDE RELIABLE AND SAFE FOAM 

CONCENTRATE INJECTION. FOR ADDED  PROTECTION AND BEFORE ATTEMPTING INSTALLATION OR OPERATION 

PLEASE FOLLOW  THE SAFETY GUIDELINES LISTED IN THIS SECTION AND ADHERE TO ALL WARNING, DANGER, 

CAUTION  AND IMPORTANT NOTES FOUND WITHIN THIS  GUIDE.

 

 

THIS SECTION ON SAFETY MUST BE CAREFULLY  READ, UNDERSTOOD AND ADHERED TO STRICTLY  BY ALL 

INSTALLERS AND OPERATORS BEFORE  ATTEMPTING TO INSTALL OR OPERATE THE  SMARTFOAM 

PROPORTIONING SYSTEM.

 

 

INCORPORATE THE  WARNINGS AND CAUTIONS AS WRITTEN WHEN DEVELOPING DEPARTMENTAL APPARATUS 

OPERATING PROCEDURES. 

 

SmartFOAM is a trademark of Hale Products,  Incorporated. All other brand and product  names are the trademarks of 
their respective

 

holders.

 

 

GUIDELINES 

READ ALL INSTRUCTIONS THOROUGHLY BEFORE  BEGINNING ANY INSTALLATION OR OPERATION  PROCESS.

 

 

 

Installation should be performed by a trained  and qualified installer, or your authorized Hale  Products service 
representative. 

 

Be sure the installer has sufficient knowledge, experience and the proper tools before  attempting any installation. 

 

Make sure proper personal protective equipment  is used when operating or servicing apparatus. 

 

A foam tank low level sensor must be utilized  to protect the Hale Foam proportioner from dry  running. 

Failure to use a 

low level sensor with  the Hale Foam system voids warranty.

 

 

DO NOT permanently remove or alter any  guard or insulating devices, or attempt to  operate the system when these 
guards are  removed. 

 

Make sure all access/service panels and  covers are installed, closed and latched tight,  where applicable. 

 

DO NOT remove or alter any hydraulic or  pneumatic connections, electrical devices,  etc. DO NOT tamper with or 
disconnect safety  features or modify protective guards (such as covers or doors). DO NOT add or remove  structural 
parts. 

Doing so voids the warranty.

 

 

Any of the above could affect system capacity  and/or safe operation of the system and is a serious safety violation which 
could cause  personal injury, could weaken the construction  of the system or could affect safe operation of  the SmartFOAM 
Proportioning System. 
 
 
 
 
 
 
 

 

Summary of Contents for SmartFOAM 1.7AHP











Reviews: