Haldex EB+ Info Centre Operator'S Manual Download Page 77

Page: 77 / 78

EB+ Info Centre flash upgrade

The EB+ Info Centre software can be updated by an
approved Haldex service centre.

Maintenance of the EB+ Info Centre

The buttons should not be pushed with any sharp
pointed objects.

Do not use harsh chemicals, cleaning solvents, or
strong detergents to clean the Info Centre.

EB+ Info Centre ADR version

The ADR version of the EB+ Info Centre has no battery
fitted and therefore cannot operate in the battery
mode. Other functions which relate to the battery,
(e.g. clock) are not available when the EB+ Info Centre
is powered from the EB+ system.

Diagnostic software

The following software should be used to programme /
setup the EBS and ABS:

DIAG+ software - Gen3 EBS and U-ABS
or
DIAG++ software - EB+ 4.0 EBS.

General

EB+ Info Centre

Operator's guide

2021

Innovative Vehicle Solutions

Summary of Contents for EB+ Info Centre















































































Search results

Summary of Contents for EB+ Info Centre

Reviews:

Related manuals for EB+ Info Centre

Brands by name

Popular brands

Haldex EB+ Info Centre, Operator'S Manual

Search results

Summary of Contents for EB+ Info Centre

Reviews:

Related manuals for EB+ Info Centre

Brands by name

Popular brands