Haldex EB+ Info Centre Operator'S Manual Download Page 43

Page: 43 / 78

Tilt angle:

Shows the angle of the trailer in degrees as read from the EB+.

It displays the angle in two modes:

›

Numerical readout

›

Arrow indication (see below)

Indicates that the trailer is leaning to the left (as viewed from the rear of
the trailer) by more than 6°.

Indicates that the trailer is vertical (as viewed from the rear of the trailer)
by less than 6°.

Indicates that the trailer is vertical (as viewed from the rear of the trailer)
greater than -2° & less than +2°.

Indicates that the trailer is vertical (as viewed from the rear of the trailer)
by less than 6°.

Indicates that the trailer is leaning to the right (as viewed from the rear of
the trailer) by more than 6°.

Press the

button to exit.

Test / Tilt angle

EB+ Info Centre

Operator's guide

2021

Innovative Vehicle Solutions

Summary of Contents for EB+ Info Centre















































































Search results

Summary of Contents for EB+ Info Centre

Reviews:

Related manuals for EB+ Info Centre

Brands by name

Popular brands

Haldex EB+ Info Centre, Operator'S Manual

Search results

Summary of Contents for EB+ Info Centre

Reviews:

Related manuals for EB+ Info Centre

Brands by name

Popular brands