background image

20

Safety Information

3

Operation

3.1

Method of operation

The Sweepmaster is a manually 
operated sweeper machine with a drive 
for the dry cleaning of hard floors and 
carpets.
The side brush (Fig. 6/4), located on the 
right-hand side of the machine, sweeps 
the dirt away from corners and edges 
into the path of the rotary brush 
(Fig. 6/3). The rotary brush (Fig. 6/3) 
sweeps the dirt into the two dirt hoppers 
(Fig. 6/2) using the overhead throw 
method. The particulate matter 
(depicted gray in Fig. 6) is forced 
against the panel air filter (Fig. 6/1) by 
the suction turbine (Fig. 6/5) and filtered 
out there. Only dust-free air is fed back 
into the ambient air.

Fig. 6

1 Panel air filter
2 Dirt hoppers
3 Rotary brush
4 Side brushes
5 Suction turbine

Sweepmaster P800

The Sweepmaster P800 is equipped 
with a gasoline engine and is filled with 
approx. 2.5 l gasoline.

Sweepmaster B800

To charge the batteries, the 
Sweepmaster B800 is equipped with a 
corresponding, fully automatic on-
board charger. To protect the battery 
against total discharge, the 
Sweepmaster B800 is provided with a 
total discharge signal transducer (TSG) 
which indicates the battery status 
during the charging process and 
discharging.

4

3

2

1

5

Summary of Contents for Sweepmaster P800































































Reviews: