background image

6

Adjusting the solder feed position

Adjustment screw 

Eccentric tuning screw 

17

How to change the solder diameter

You can change the solder diameter by replacing the teflon tube, the solder feed guide set or

the solder feed pulley unit. 
The compatible solder diameters varies by model number of the HAKKO FU-500. 

Please check your model number and then see the part list on the back cover of this manual when

you need some part replacement. 

Loosen

Loosen

Loosen

How to install the teflon tube

Turn the solder feed guide nozzle counterclockwise and remove the solder feed guide support.

You can now install the teflon tube. Lastly, insert the guide pipe.
The teflon tube is quite long in length. Cut the excess length of the teflon tube to leave an appropriate

length (about 3 to 5 mm) from the guide pipe before use.  

Guide pipe

Guide tube

Solder feed guide support

Teflon tube

Solder feed guide nozzle

. Loosening the adjustment screw 

 will allow you to move the entire solder feed guide set as shown

in the figure below. Move the solder feed guide set to the tip. 

. Loosening the adjustment screw 

 will allow you to move the guide pipe as shown in the figure

below. Move the guide pipe until solder comes into contact with the tip.

Turning the eccentric tuning screw 

will turn the feed position adjuster

together, allowing you to make tuning. 
(This screw cannot be removed.)

Adjustment screw 

Only use compatible solder of specified size. 

Failing to do so may cause a failure.

The attachment of the solder feed pulley unit

for φ0.3mm (BX1000) is different.

Refer to the “How to set solder” in the BX1000.

Feed position adjuster

Eccentric tuning screw

 ③

Make sure that the teflon tube protrudes from the guide pipe before use. 

Otherwise, the guide pipe may be clogged with solder. 

It is important to use a cutter knife instead of scissors to cut the teflon tube carefully in order to prevent

the end of solder wire from being squished.

Cut

About 3 to 5 mm

CAUTION

CAUTION

Hex wrench size : 2.5mm

Summary of Contents for FU500-71X

























Reviews: