Haiyang HIS-75A Manual Download Page 63

Page: 63 / 75

- 59 -

Installation

Drill a 1/4 in. diameter hole at each marked location. Mount the HIS-75A display bracket using bolts

through the mounting surface. Place large flat washers on the opposite side of the mounting surface

from the bracket and then install lock washers and nuts. Tighten securely.

Install the display unit into the mounting bracket. Check alignment and operation of the pivots and

security of the mounting. Make any adjustments necessary to prevent binding and assure even

meshing of the pivot locking washers. It is advised to remove the display unit and store it in a safe

place to prevent damage during the rest of the installation process.

- Power Connection

Power is supplied to the HIS-75A System through a connector on the rear panel of the display unit.

Route the power cable from the HIS-75A

location to the ship‟s power distribution panel.

Connect the black wire to a battery negative (-) terminal of the power panel.

Connect the white wire to a fused battery positive (+) terminal of the power panel ( 12 to 24 Vdc

nominal). If a fused terminal is not available, install an in-line fuse holder.

Summary of Contents for HIS-75A












































































Search results

Summary of Contents for HIS-75A

Reviews:

Related manuals for HIS-75A

Brands by name

Popular brands

Haiyang HIS-75A, Manual

Search results

Summary of Contents for HIS-75A

Reviews:

Related manuals for HIS-75A

Brands by name

Popular brands