background image

MB6 (6-Slot) Chassis 

MB6 Installation 

MB6 and MB21 Multichannel Chassis Installation Guide, v2.0, Issue 01

10

To power up the F-MB6X-RAC or F-MB6X-MED Chassis:

1.

Make sure the power switch(es) on the back of the chassis are in the OFF (2) position.

Figure 2: F-MB6X-MED Chassis Rear View showing Power Connector

Figure 3: F-MB6X-RAC Chassis Rear View showing Power Connectors

2.

Connect the power cord(s) to one (or both) of the power receptacles shown in Figures 

2

 and 

3

.

3.

Plug the cord(s) into a grounded AC power source.

4.

Turn one (or both) PSU Power On/Off switches to the ON (1) position.

On the MB6-RAC, the PSU Status LEDs will turn green indicating that the chassis is powered up.

In the front of either chassis, the Status LEDs will start blinking green, indicating that the encoders/decod-
ers/gateways are booting up. 

5.

Wait until the Status LEDs stay solid green, indicating that the chassis is ready for operation. 

To power up the F-MB6X-DC-DC Chassis:

1.

Make sure the power switch is in the OFF (2) position.

Figure 4: F-MB6X-DC-DC Chassis Rear View showing Power Connectors

PSU Power On/Off Switch

AC Power Receptacle 

PSU Power On/Off Switches

AC Power Receptacles 

PSU Status LEDs (green)

PSU Fault LEDs (red)

PSU Power 

Positive and Negative Connectors

Ground Lug

On/Off Switch

PSU Status LEDs (green)

PSU Fault LEDs (red)

Summary of Contents for MB21






























Reviews: