background image

A. POWER ON/OFF
Touch this button to swith on the power if the machine is not on power, and touch this
button to switch off the power if the machine is on power.

B. PROGRAMME
Touch this button then you can select the washing programs as you wish from top to
bottom in proper order. The backlight is bright while the program is selected. The
machine will carry out the standard program if there is no program to be selected.
Attention: The machine has the memory function for the "Habit" program.

C. DRY

The sequence of the dry program as follow as each time the button is touched after the
washing program is set:
Whole auto dry program.
The standard program for the individual dry.
At this moment you can select either 60 min or 30 min program.
You can not select dry function while you have already selected the heavy or delicate
program.
Attention: The maximal quantity of the laundry is 2.5Kg if the dry function is selected.

D. DRAIN

The different spinning speed can be selected by touching this button. For details please
see the program setting guide.
The spinning speed is 1200rpm ( 900rpm for night washing ) if the dry function is
selected.

E. RINSE
Touch this button to select the rinsing time. The time is changeable each time when it is
touched and 6 times are the maxim.

F. WASH
Touch this button to select the washing time. Increasing the washing period each time
this button is pressed. The increasing step is one minute for one press.

Control panel

Laundry loading

Evenly load the laundry in the
washing machine and then
tightly close the door of the
washing machine.

Overalls

(cotton 950g)

Blended

(fabric clothes
800g)

Shirt

(cotton 300g)

Jackets

(cotton 800g)

Woolen

(blankets 3000g)

Single bed
sheets

(cotton 800g)

Socks

(blended fabrics 50g)

Underwear

(blended fabrics 70g)

Shirts

(300g)

Pajamas

(200g)

Jeans

(800g)

Reference loading

Notice:

1) When first using the
washing machine, let it run
unloaded for one program to
prevent the laundry from being
tainted by oil or dirty water from
the washing machine.

2) Do not overload the washing
machine.

Put detergent in the cartridge

There are three partitions in the detergent cartridge:
Partition 1 : It is used for the prewash function.
Partition 2 : Put the detergent in this partition no
matter whether the prewash function is selected or not.
Partition 3 : Put the softening agent in this partition if the
launry has gone through the soften process.

Washing program setting

Set the washing program correctly in accordance with the laundry load.
First connect the mains and depress the power on/off button, the machine will work on
the defaulted standard program. Depress the program selection button for the required
washing program.

Notice: The above operation should be under the condition of no power down. The ma-
chine will continue its previous program if the machine has the memory function after
the power down. The memory function can be canceled by turning off the power and
restart it.

Installation

Caution:

1) Do not add liquid degergent into partition 1 and partition 2
2) For prewashing program, detergent should be added to both partition 1
and 2; for other programs, do not add detergent to partition 1
3) Do not overuse softening agent as this may damage artificial fabrics

6

11

Remaining time:Min

DELAY

TEMP

PREWASH

Water level

WATER

LEVEL

Door lock

Standard

Habit

Quick

Night

Heavy

Delicate

START
PAUSE

POWER
ON/OFF

PROGRAMME

Standard

30min

60min

DRY

DRAIN

RINSE

WASH

Time

Min

00

rpm

Summary of Contents for XQG50-S1216











Reviews: