6
49-5000786 Rev. 0
ENGLISH
11. Louver SIDE/SIDE Button
Feature is not available.
Press the LOUVER SIDE/SIDE button to choose the
position of the vertical airflow louvers. Status display of
air flow
COOL/DRY/HEAT/FAN
NOTE:
• When humidity levels are high, condensate water may
occur at the air outlet if all vertical louvers are adjusted
to far left or right.
• When turning the unit on, the remote control will
automatically return the louver to the previous set
position.
12. SLEEP Button
1. Operation in COOL or DRY modes: One hour after
SLEEP mode starts, the temperature will rise 2°F
above set temperature. After another hour, the
temperature rises additional 2°F. The unit will run
for additional six hours before it turns off. The final
temperature is 4°F higher than initial set temperature.
Using this feature helps with achieving maximum
efficiency and comfort from your unit while you sleep.
In COOL, DRY mode
SLEEP operation starts
SLEEP operation stops
Unit stop
Temp. setting
Rises 2ºF
Approx. 6 hrs
1 hr
1 hr
Rises 2ºF
2. Operation in Heat Mode: One hour after SLEEP mode
starts, the temperature will decrease 4°F below set
temperature. After another hour, the temperature
will decrease an additional 4°F. After an additional
three hours, the temperature will rise by 2°F. The unit
will run for an additional three hours before it turns
off. The final temperature is 6°F lower than the initial
set temperature. Using this feature will help with
achieving maximum efficiency and comfort from your
unit while you sleep.
In HEAT mode
SLEEP
operation starts
SLEEP
operation stops
Unit stop
Temp. setting
Decreases 4ºF
Decreases 4ºF
Rises 3ºF
3 hrs
3 hrs
1 hr
1 hr
3. In AUTO mode, the unit operates in corresponding
sleep mode adapted to the automatically selected
operation mode.
NOTE:
• When the unit is set to sleep mode, the fan speed will
be set to low speed and cannot be changed.
• When the TIMER function is set the sleeping function
cannot be set. If the sleeping function has been set and
the user sets the TIMER function, the sleeping function
will be canceled and the unit will be set to the timer
function.
13. Fahrenheit/Celcius Button (Only applicable to large
cassette panel models)
Press F/C to toggle remote and unit display
temperature between Fahrenheit and Celsius.
14. EXTRA FUNCTION Button
Press the EXTRA FUNCTION button to view all other
operations. Press CONFIRM/CANCEL to select and
save the chosen operation. If no button is pressed for 10
seconds, the remote will exit EXTRA FUNCTION mode.
A) Refresh air
B) A-B selection - This will allow you to control two
separate units with a single remote control. Note: This
feature would be setup at the time of installation by
the contractor. - Feature not available on this series.
C) Auto mode
- The heat pump will automatically
select Cool, Heat, or Fan operation according to set
temperature. When FAN is set to AUTO the heat
pump automatically adjusts the fan speed according
to room temperature.
D) Upper and Lower louver lock:
1. Upper louver lock will lock the horizontal louver
in the top position. Commonly used during cooling.
2. Lower louver lock will lock the horizontal louver
in the lower position. Commonly used during
heating.
3. To unlock the louver press EXTRA FUNCTION
button until either a single louver icon or
oscillate icon .
Note: When the louver is locked, the position
cannot be changed with the LOUVER UP/DOWN
button.
E) Timer ON/OFF: Sets a countdown timer until the unit
is turned ON/OFF. TEMP+/TEMP- button is pressed
with the length of time increment/decrement in 0.5
hour between 0-12 hours, and 1 hour increment/
decrement between 12-24 hours.
1. When the remote is set to ON, the system will
turn off until the countdown timer ends. Then the
indoor unit will turn on and operate in the mode,
temperature setting and fan speed that was
displayed when timer was set.
2. When the remote is set to OFF, the system will
remain ON until the countdown timer ends.
REMOTE CONTROL FEATURES AND SETTINGS
Summary of Contents for WJ01X24721
Page 2: ...2 49 5000786 Rev 0 ENGLISH...
