Haier Sea Elephant PJF2-150W User Manual Download Page 4

1

1.Home water heater:

Collector equipment is aslant installed  on the rooftop and perfectly integrated 
with building, match  the building standard and fashion nowadays.

2.

Vacuum glass

 tube  is efficient and reliable:

The conductive efficiency of the tube  is supernale. Vacuum tube of collector 
equipment is without water and dirts, antifreeze, high endurance, efficient and 
secure.

3.Selective coat endothermic system

The endothermic system adopts the latest international high-tech. It is 
characterized by high absorbing capacity and low reflectivity.

4.Heat water system of enduring pressure:

Water can be supplied in more than one line. The flux of water is enough to use, 
the usage of  water is comfortable  and  the regulation of water temperature is 
convenient. System run reliably and can be used under all-weather .

5

.scientific designing:

Four kinds of working modes are designed to supply water under different 
season.Control the running of pump automatically according to different 
temperature , enconomizing energy and prolonging life of pump. Possess the 
function of digital display of water temperature and multisafeguard, safe to 
use,easy to use.

14

Electric circuit diagram  

Notes for  usage

 the serving person.
8.When the system runs continually over one month, you are suggested to 

check regularly whether the deviation of the clock is large so as to adjust the 
clock promptly and ensure that the preset and intellectual heating modes 
operate normally.

9.In cases when the power supply line of the appliance is damaged, it is the 

personnel of after service who change that for specially designed lines 
(provided by the manufacturer).

10.In cases when the temperature of water-storing tank exceeds 85

, and the 

electrical enclosure indicates E2.First,you should cut off power supply, 
then,to release a little of hot water and supply some cold water.when the 
temperature of water is decrease and then to connect  power supply ,the 
fault is able to obviate. 

11.The temperature difference for running of circulating water pump suggests 

that the temperature should be chosen as 15 

 in seasons when the 

sunshine is strong(eg, summer), and 10

in seasons when the sunshine is 

weak (eg, winter).

12.When water heater is not used for long and you use it again, to avoid 

occurrence of accidents,you shoud exhaust the system, and the system must 
be full of water before usage,let the gas which lie in the pipe out,meanwhile, 
make sure there is no smoke, fire or other appliances near when you open 
the valve,the exhausting way: open the hot water outlet  and cold water inlet  
valve, when the water come out sustaining after exhausting all the gas, then 
close the hot water outlet valve.  you had better operation the valve in the low 
tempreture,such as wee hours or night, or the life of the system will be 
influenced. to check  all the parts of the system in good condition, and make 
sure the tank full of water, then you can  use it.  

13.Operation exhaust valve termly so as to clear dirty thing, and insured to 

exhaust valve  be not block off.

C o n t r o l l e r
Display Board

L:
N:
E:  
K1

K2

R

EH:H
MT:High 
RT1:T
RT2:C

  Brown  Wire

  Blue  Wire 

YelloW/Green  Wire 

elay

eating Element

Temperature Limiter

ank Temperature Sensor

ollector Temperature Sensor

RT1

RT2

K1

K2

Pump

E

L

N

C o n t r o l l e r
Wire Board

le

a

k

a

g

e

 I

n

s

_

P

e

c

tio

n

 L

o

o

p

Summary of Contents for Sea Elephant PJF2-150W











Reviews: