background image

 

 

14

9. DVD Part: Introduction of MTK1389D maintenance   

NOTE:  MTK1389D  is  a  type  of  LSIC  for  DVD  decode  .MTK1389D  IC  consists  of 
RF,SERVO,DSP,DECODE,VIDEO DAC and AUDIO DAC.

 

1. 

Under normal power supply conditions, the maintenance plan for MT1389D mono-chip is: first the reset 

circuit resets the MT1389D, after the crystal oscillator circuit gave the clock signal to MT1389D, MT1389D will 
start the initialization check for Flash

E

2

PROM

SDRAM, after everything is checked to be normal, it will start 

initialization check for built-in Audio DAC, servo and motor Driver IC . 

2. 

If  the  all  the  a.m.  parts  are  good,  then  MT1389D  will  send  signal  to  motor  Driver  to  drive  the  servo 

system

pick up then to generate DVD light for collection, tracing the main shaft to check if there is any disc, and 

confirm if it is CD format or DVD format disc. If the disc is in DVD format, the system will read the data from the 
disc directly; if it is in CD format built-in servo will drive the CD laser to send out CD light and read the data, the 
data then will be amplified through built-in RF amplifier and sent to MT1389D decode part for data processing, 
released by MPEG and resolved into video data and audio data, then they will be returned to analog signals 
through        built-in VIDEO DAC

AUDIO DAC. 

 

Decoder section 

3. 

There is power supply, clock and reset, but the system does not work. 

1

 

Check  if  all  the  address  wires  required  for  FLASH  are  exist,  and  if  they  are  in  normal  status, 

especially check if the A0~A15 of FLASH have normal signals, if there aren

t, then inspect MT1389D to see if 

there is faulty soldering. If there are normal signals at A0~A15, check if the address data  signal of MT1389D 
and SDRAM is normal. If it is normal, then check the signal at A16~A19 of MT1389D; if there are also signals, 
then check the video output    wires and AV filter circuit; if there is no signal, then check the corresponding pins 
of MT1389D to see if there is any short circuit, break or faulty soldering. 

4. 

System in normal operation, but the audio has no sound. 

1

 

Because the AUDIO DAC is built in MTK1389D IC.you need to check the lower passing amplifying 

circuit and the MUTE circuit at the back of the LPF circuit. Also check if there is any power supply to the LPF 
circuit. 

2

 

Check if the power supply voltage required for playing is at normal level. 

 

Servo Section 

5. 

After the LOGO of the machine shows normally, there is no OSD display. This problem mainly is caused 

by the abnormality built-in RF and servo, possible problems may be: 

1

 

Built in RF and its surrounding circuits have problems. 

2) 

Servo part of MT1389D has problems. 

6.      OSD display is normal

while there is no action of servo part

feeding motor does not work, main shaft does 

no turn, possible fault status are: 

1) 

The corresponding signals giving by MT1389D to DMSO

FMSO are missing, the reason may be the 

problem of MT1389D or the communication between MT1389D and motor Driver IC SA5668. 

2)   

Not  output from  Motor  Driver,  the  reason  may  be  the problem  on motor  Driver  or its  corresponding 
circuit. 

 

7. 

Servo part in good status, while there is no pick up action

no light, no focus

 

1

  No light, check the power supply

power supply for pick up

, or the light producing driving circuit to see 

if they are in normal status. 

 

  

      2

  No focus, check MT1389D to see if there is signal output from FOSO

TRSO. 

Secondly, check motor driver to see if there is F+

F-

T+

T-signal output. 

Thirdly, check the external corresponding circuit of the motor driver to see if there is any problem. 

 

8. 

All the servo part has action, while it cannot read out the disc 

1

   Check  MT1389D  if  there  is  RF  net  picture  output,  if  there  isn

t,  then  it  must  be  the  problem  of 

MT1389D and external surrounding circuits, it there is output, then it might the problem of MT1389D 
and its surrounding circuits. 

2

  There is RF signal

but not in normal status

then check MT1389D and surrounding circuits. 

3

    Everything is normal, but the disc cannot be read out, check MT1389D and its surrounding circuit 

 
 
 
 
 
 
 
 
 

                    

                                             

                          

Summary of Contents for MX-TM7414Mpeg4

















Reviews: