background image

-2-

SAFETY AND WARNINGS

IMPORTANT SAFETY INSTRUCTION

1)  Read these instructions.

2)  Keep these instructions.

3)  Heed all warnings.

4)  Follow all instructions.

5)  Do not use this apparatus near water.

6)  Clean only with dry cloth.

7)  Do not block any ventilation openings, install in 

accordance with the instructions.

8)  Do not install near any heat sources such as radiations, 

heat registers, stoves, or other apparatus (including 

amplifiers) that produce heat.

9)  Do not defeat the safety purpose of the polarized plug. If 

the provided plug does not fit into your outlet, consult an 

electrician for replacement of the obsolete outlet.

10) Protected the power cord from being walked on or 

pinched particularly at plugs, convenience receptacles, 

and the point where they exit from the apparatus.

11) 

Only use attachments/accessories specified by the 

manufacturer.

12) Unplug this apparatus during lighting storms or when 

unused for long periods of time.

13) 

Refer all servicing to qualified service personnel. 

Servicing is required when the apparatus has been 

damaged in any way, such as power-supply cord or plug 

is damaged, liquid has been spilled or objects have fallen 

into the apparatus, the apparatus has been exposed to 

rain or moisture, does not operate normally, or has been 

dropped.

14) Mains plug is used as the disconnect device, the 

disconnect device shall remain readily operable.

15) The ventilation should not be impeded by covering the 

ventilation openings with items, such as newspapers, 

table-cloth, curtains, etc.

16) 

No naked flame sources, such as lighted candles, should 

be placed on the apparatus.

17) Attention should be drawn to the environmental aspects 

of battery disposal.

18) The use of apparatus in moderate climate.

19) The apparatus shall not be exposed to dripping or 

splashing and that no objects filled with liquids, such as 

vases, shall be placed on the apparatus.

This symbol indicates that this product incorporates 

double insulation between hazardous mains voltage and 

user accessible parts. When servicing use only identical 

replacement parts.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO 

NOT  REMOVE COVER (OR BACK).NO  USER 

SERVICEABLE PARTS INSIDE. REFER SERVICING 

TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

 

         DO NOT OPEN!

CAUTION

CAUTION

The symbol indicates that dangerous voltages  

constituting a risk of electric shock are present 

within this unit.
The symbol indicates that there are important 

operating and maintenance instructions in the 

literaturaccompanying this unit.

WARNING:

To reduce the risk of fire or electric shock, do not expose 

this apparatus to rain or moisture.

WARNING:

 

The batteries shall not be exposed to excessive heat such as 

sunshine, fire or the like.

Please act according to your local rules and do not dispose of 

your old products with your normal household waste.

Correct disposal of your old product helps to prevent 

potential negative consequences for the environment and 

human health.

This product complies with all implemented RoHS type 

regulations worldwide, including but not limited to, EU, 

Korea, Japan, US States (e.g. California), Ukraine, Serbia, 

Turkey, Vietnam and India.

We continue to monitor, influence and develop our processes 

to comply with upcoming proposed RoHS type regulations, 

including but not limited to, Brazil, Argentina, Canada.

Restriction on Hazardous Substances statement (India)

 

This product complies with the “India E-waste Rule 2011” 

and prohibits use of lead, mercury, hexavalent chromium, 

polybrominated biphenyls or polybrominated diphenyl ethers 

in concentrations exceeding 0.1 weight % and 0.01 weight % 

for cadmium, except for the exemptions set in Schedule 2 of 

the Rule.

Summary of Contents for LE43B7600A


























Reviews: