background image

4

Please insert the power cord into special 
receptacle with rated voltage.Be sure to 
use single-phase two pins  receptacle.
The earthing terminal must be earthed 
reliably.If possible,please adopt electric 
leakage protector.

When the machine is normally using, please
put  the power plug  at the location easily to 
be inserted and extracted by hand. Be sure
to pull the plug off when there'spower failure, 
or the machine is being moved, cleaned or
when it is idle.

SAFETY PRECAUTIONS

If  the power cord is bad, to avoid risk it is required to replace.
 Keep the pin of the power plug clean.

In case the washing  machine is  installed
on  ground  with  carpet ,  do not block the 
ventilation  hole  with  carpet.

Ventilation hole at 
the  bottom of the 
washing machine

Do not use water hotter than 50 C .

Do not share one receptacle with other
electric  appliances.   Do  not  use it in 
case that the power  plug is damaged 
or  the inserting  into the receptacle is
loose.

Do not wash water-proof laundries such
 as the raincoat, bicycle shelter etc.  To
 avoid abnormal vibration during spinning.

Do  not  put  the  machine  at  damp  place 
like  the  bathroom .  Never  wash  it   with 
water. Do not place wet laundries on the 
control panel.

Summary of Contents for HWM65-187S


















Reviews: