Haier HWM100-828A User Manual Download Page 4

2

Safety precautions

50 C

 

T h e   v e n t i l a t i o n
 holes at the bottom

Carpet

Do not let the machine share one receptacle with other
 electric appliances. If the plugging into the receptacle
is  loose, do not use the plug any more.

Do not wash water-proof laundries like 
the raincoat, bike covers etc. to avoid
 abnormal vibrations in spinning.

Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with
 dry cloth carefully.
If  the power cord or the power plug is bad, to avoid risk it is required to have it replaced by  
the technicians of  our  special shop or  our customer care agent. 

Do not put the machine at damp place like 
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.

Do not use water hotter than 50

.

In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.

Please plug the power plug on special 
receptacle. Be sure to use three-pins 
power receptacle. Ensure that the earthing 
prong of the power receptacle is earthed 
reliably. Use leakage protector if possible.

 The washing  machine must  be positioned so that
 the  plug is accessible. Be sure to pull the plug off 
 and close the water faucet in following cases: 
 power failure, delivering the machine, setting the 
 machine idle or cleaning the machine. Do not plug 
 or pull the power plug with wet hand.

15

Disposal after washing 

After using, please clean the lint and foreign materials of the lint filter etc. in time. 
Otherwise it may influence your using the machine.

Please first pull off the power plug from the receptacle before cleaning.

Clean the detergent box and set it on

the control panel seat.

1.The method of dismantle: Push it up aslant and gently.

2.The method of install : install it upwards and aslant 

                                          and push it in .

The filter screen of the water inlet valve is likely to be 
blocked  by foreign materials and influence the water 
inlet. 
Please clean it with brush every two months.

If the cabinet is dirty, wipe it with wet cloth
     Do not flush it directly with water.
     Wipe it with neutral detergent.
     Do not wipe it with thinner, petrol, alcohol etc.

Lint filter:

The lint filter must be used during washing.

It must be cleaned in time after each using.

Figure 1 

Figure 2

Down

Dismantle

Install

 The back cover of lint filter

Install

Dismantle

Down

Up

Up

 The front cover of lint filter 

1.Push down the spring piece of the top lint filter 
to make the claws out of the filter cover, and then 
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can 
get down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it 
tight .
6.Make sure the lint filter well installed, or it can 
influence your use.

1.After washing, close the water faucet.  ( If needed, you can dismantle the water inlet hose).

5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time 
(about 1 hour), then close the top lid.

4.Hang up the power cord and drain hose.

3.Be sure to pull off the power plug before maintenance.

2.Do not store water in the washing machine for a long period.  Drain  the  water  completely after each using.

Thinner

Petrol

Alcohol

Dismantle

Install

Summary of Contents for HWM100-828A











Reviews: