DISPLAY CODES AND SPECIAL FUNCTIONS
¬ Control panel lock function: Press the "Delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a program.
It can no longer be changed by operating buttons or knobs. To unlock press the "Delay" and "Start/Pause" buttons again for 3
seconds.
¬ Power-off memory function: In case of abrupt power failure or the need to cut off the power during a program cycle, the present
settings will be saved and the preset operation will resume when the power is on again.
¬ To cancel a program
Press the "Start/Pause" button, then switch off the power and the program is automatically cancelled. Turn the program selector
again to choose another program.
Note: During the spin process, if too much foam is inspected, in order to protect the motor, the washing machine will eliminate the
foam automatically; the motor will stop and the drain pump will drain the water continuously for 90 seconds. If it happens more than
3 times, the motor will stop until the end of cycle without spinning.
CODES
S
N
O
IT
U
L
O
S
S
E
S
U
A
C
Err1
¬ Door is not properly shut.
_ Shut the door properly and then press the Start/Pause button.
Err2
¬ Drainage error, water not emptied within 6
minutes.
_ Clean the filter and check the drain hose for blockage. If error
still exists, please contact the maintenance personnel.
Err3
¬ Temperature sensor not properly connected or
damaged.
_ Contact the maintenance personnel.
Err4
¬ Heater error (Appears at the end of a cycle).
_ Contact the maintenance personnel.
Err5
¬Water level not met in 8 minutes.
¬The height of the drain hose is below 80 cm.
¬ The drain hose is in water.
.l
a
m
r
o
n
si
er
u
s
s
er
p
re
t
a
w
d
n
a
,
n
o
d
e
n
r
u
t
si
p
a
t
t
a
h
t
er
u
s
e
k
a
M
_
If problem still exists, please contact the maintenance personnel.
_ Install drain hose within 80-100 cm of height.
_ Make sure the drain hose is not in water.
.l
e
n
n
o
sr
e
p
e
c
n
a
n
e
t
ni
a
m
e
h
t
tc
a
t
n
o
C
_
.r
o
rr
e
r
o
t
o
M
¬
7
rr
E
Err8
¬ Water exceeds protective level.
_ Contact the maintenance personnel.
End
¬ End of wash cycle.
1:25
¬The remaining time is 1 hour 25 minutes.
19:30
¬Status information:Preset time for delayed operation.
UNb
After the last rinsing cycle finishes,spinning fails completely due to unbalance of the laundry.
.l
e
n
n
o
sr
e
p
e
c
n
a
n
e
t
ni
a
m
e
h
t
tc
a
t
n
o
C
_
0
1
rE
¬ The signal of Water level sensor is wrong.
Note: Aqua proof pan: There is a float switch on the Aqua proof pan, while the wachine machine start
to leakage, the float switch will detect and start to work, the devices stop working (including motor,
heater, magnetic switch, etc. ) the washing machine indicates "Er16" , only water outlet pump still
working.
Please contact the maintenance personnel.
_ The unit automatically closes all valves and drainage pump
starts.
Er16
¬Leakage alarm.
Summary of Contents for HW60-1482
