Haier HW50-1010 Installation And User Instructions Manual Download Page 13

12

User Instructions

Using your washing machine

1. Loading
a: Open the door, place laundry item by item 

into the washing machine, firmly close the door.
b: Do not overload the washing machine (see 

the programme selection guide for maximum 

load information, page 10).

2. Add detergent
Pull out the detergent drawer, add the detergent

and softener to the corr ect compartments.
1: Main wash detergent
2: Fabric softener 
3: Prewash detergent

Refer to the table on page 10, the detergent

manufacturers recommendations and the care

labels on your clothing. 
Caution:  Do not add liquid deter gent to 

compartments 1 or 3.
Only add detergent to compartment 3 when 

washing cotton in either ‘intense’ or ‘prewash’

programmes.

3. Select a washing programme
The appropriate programme should be selected 

according to the type of laundry .

4. Select a spin  speed
Touch this button lightly to select the desired 

speed. When a speed is set, the indicator light 

will be light on.

5. Intense button

Touch this button lightly, the indicator light will 

be light on . you can increase the washing time,

rinsing times  in main wash stage of the selected 

program, which is suitable for dirty clothes.

1

2

3

5

4

C

90

C

60

C

40

C

40

C

30

C

90

C

60

C

40

C

40

C

30

Summary of Contents for HW50-1010




















Reviews: