background image

Matters Needing Attention

ƽ8VH

Trouble-shooting

The following circumstances do not constitute problems. Do not contact the maintenance service

until the problem has been confirmed.

Problem

Possible cause

The

washing

machine

fails

to

operate

 

Poor connection to power supply

 

Power failure

 

Door is not properly closed (Err 1)

 

Program knob has not been switched on (it is not
turned past “0”)

Washing machine cannot be filled
with water

 

Water tap is not turned on

 

Water pressure is less than 0.05Mpa

 

The inlet hose is kinked

 

Water supply failure

 

The program knob is not properly set

 

The door is not properly closed

 

The inlet hose filter is blocked

 

The program is not started

The machine is draining while is
being filled

 

The height of the drainage hose is below 80cm (it
should be within 80-100cm)

 

The drainage hose end is in water

Drainage failure

 

Drainage hose is blocked

 

Drainage hose end is below 100cm above the floor
level

 

The filter is blocked

Strong vibration during spinning

 

Not all packing bolts have been removed

 

Washing machine is located on an uneven surface or is
not level

 

Machine load is over 5kg.

 

Operation stops before completion
of a wash cycle

 

Water or electricity failure

 

Washing machine is in a soaking cycle

 

Washing machine gives an error message.

Excessive foam in the drum, which
is spilled to the distribution drawer

 

The detergent is not a low-foaming type or for manual
wash

 

Excessive use of detergent

8. The washing machine must not be used
in the open or in area of high moisture as
water droplets may form on electrical
components,Air dry the appliance if the
washing machine components become
wet.

9. The washing machine should be place
in a well ventilated area maintaing a
space between walls or furniture.

10. Keep away from heat sources and di-
rect sunlight to prevent plastic and rubber
components from aging.

11. During installation, ensure that the
electric cable is not trapped by the wash-
lng machine and avoid damage to the
electric cable.

1. Make sure that the washing machine is

securely connected to the water supply,
take the necessory precautions or con-

tact the local service center if the con-

nection is poor or there is a water

leakage.

2 Keep the door slightly open when the washing

machine is not being used. Never cover the ma-
chine with a plastic sheet.

Summary of Contents for HT1600TXVE













Reviews: