Haier HDY-D70-F Operation Manual Download Page 7

12

1

.

Cleaning the surface

Wipe the body of the dryer and the  control panel with a damp cloth. 

Remember not use any organic solvent or corrosive agent  to avoid 

damage to the machine.

2. Cleaning the filter screen

   To ensure a good ventilation during drying,

 the filter screen must be cleaned after every

 drying program is complete.

   Open the door and remove the filter screen 

from the machine. Open the screen and clean 

off the dust on the screen with a wet towel. After

cleaning, put the screen back in place.

3. Emptying the water collection box

    During operation , steam condenses into 

water and is collected in the box.The box must 

be emptied after the program is complete. 

 -Hold the handle and pull the box outwards to 

remove it. keep it level to prevent the water 

from overflowing;

 -Pour away water. Note: the 

water can not be used for drink or for food

processing;

 -Put the box back in place.If the box has not 

been emptied, the dryer will sound an alarm 

when the box is full. The indicator light comes 

on while the box is emptied and the dryer will 

stop. It will not restart until the box is emptied.

4.Cleaning the condenser 

The condenser must be cleaned monthly.

Switch off the  power supply before cleaning.

 -Hold the protrusions on both sides of the 

lower deco panel and open it.

13

 -Using a coin or other tool, push the slides on the cover to the position 

as shown in the figure and then remove the cover;

 -Turn the condenser's handle 90 degrees in the direction as shown in 

the figure;

 -Remove the condenser from the dryer;

 -Clean the condenser with a brush or flush with by a water jet;

Note: Do not use a sharp tool in cleaning the heat exchanger, otherwise

 it may damage its sealing performance;

 -Put the condenser back in place and lock up the cover;

 -Put the lower deco panel back in place. 

5. Cleaning the drum

After the dryer has operated for 

a time, fabric caring agents or

calcium contained in the water will

form an almost invisible  layer on 

the inside of the drum. 

This makes the dryer not able to 

reliably and accurately identify the

dryness of the laundry. So the inside 

of the drum, especially the stainless

steel pieces on the blades must be 

cleaned regularly by a wet cloth.

B

C

D

A

Cleaning and Maintenance

Cleaning and Maintenance

Summary of Contents for HDY-D70-F










Reviews: