background image

WARNING AND CAUTIONS

Do not decompose, repair or alter the
machine by yourself.

Do not stretch hands into the working 
machine.  It is dangerous even if  the 
rotation is slow. Take  special care of
the children.

Do not put any hot or heavy items (such 
as  the  kettle  with  hot  water )  on  the 
washing machine.

The  handicapped  or  children  without
 care shall not use the machine.

Under certain conditions, hydrogen gas may be produced in a hot water system that has
not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If  the hot water 
has not been used for such a period, before using the washing machine, turn on all hot 
faucets and let the water flow from each for several  minutes. 
This will release any accumulated hydrogen gas. As the gas
is flammable, do not smoke or use an open flame during this time.  

Keep the machine away from direct
sunlight and heat source like the heater.

Do  not  wash  articles  that  have been 
previously cleaned in, washed in, soaked 
in, or spotted with gasoline, dry-cleaning 
solvents, other  flammable, or  explosive 
substances as  they give  off vapors that 
could  ignite  or  explode. Do  not  add 
gasoline, dry-cleaning solvents, or other
flammable, or  explosive substances  to
the wash water. These substances give
off  vapors  that could ignite or explode.

Petro

l

Thinner

Summary of Contents for GWT900AB






















Reviews: