background image

 

 

„

 

Product features

 

1.  Inner cylinder made of SUS304 stainless steel 
The inner cylinder of the water tank adopts sanitary SUS304 stainless steel, featuring strong 
corrosive resistance and durability. 
 
2.  High efficiency & energy-saving thermal insulation 
With integrated polyurethane foam insulation for solar water heaters, realize good heat 
preservation and minimize heat loss. 

3. Aluminium-Zinc-coated 

outer shell of water tank 

Aluminium-Zinc-coated sheet boasting outstanding corrosion resistance, oxidation resistance 
and weatherability is the first choice for outdoor protective materials. 

4.  Tower type frame 
The tower type frame, made of carbon steel by means of spray processing, has the advantages 
of a stable structure, attractive appearance and corrosion resistance. 
 

„

 Technical 

parameters 

Note:The deviation of the aperture area is 

3%; the deviation of the capacity is ±5%; the 

permitted error limit of other parameters is ±10%. 

 

„

 Installation 

instructions 

‹

  Selection of installation location

 

 

1.The water heater shall be installed within the 
lightening protected area of a building in locations 
prone to lightning strikes. 
2.The orientation of the water heater to be installed: 
10° south by east and 15° south by west. 
3.There must be no shielding object in front of the 
installation location of the water heater. If an object 
exists, the space between the heater and the 

objective shall be more than L, 

 

(wherein: H-height of the shielding objective; 

α

-local 

latitude)

 

Models 

GV110RNMB 

GV150REMB

GV200REMB 

GV270REMB 

Specifications 
of the glass 
vacuum tubes 

Φ

58mm X 1800mm, all-glass vacuum tube solar heat collector 

Frame form 

Horizontal 45° 

Number of the 
glass vacuum 
tubes 

12 16  22  30 

Aperture area 

1.58m

2

 

2.07 m

2

 

2.90 m

2

 

4.03 m

2

 

Usable water 

110L 

150 L 

200 L 

270 L 

Total water 
volume 

141 L 

195 L 

253 L 

342 L 

Electric 
auxiliary 
heating 

None 

Power of electric auxiliary heating: 1650W/230V 

Product features • Technical parameters • Installation instructions 

Summary of Contents for GV150REMB









Reviews: