background image

Page 24 of 24

508296-G01 / 31-5000753

Issue 2231

Start-Up and Performance Checklist

Customer: _____________________________________

Address: _______________________________________

Indoor Unit Model: _______________________________ Serial: _________________________________________
Outdoor Unit Model: ______________________________ Serial: _________________________________________
Notes: __________________________________________________________________________________________

Start-Up Checks

Refrigerant Type: _____________________
Rated Load Amps: ____________________ Actual Amps: ______ Rated Volts: _______ Actual Volts: ________
Condenser Fan Full Load Amps: _________ Actual Amps: ______

Cooling Mode

Suction Pressure: ____________________ Liquid Pressure: _________
Supply Air Temperature: _______________ Ambient Temperature: ___________ Return Air Temperature: _________

System Refrigerant Charge (Refer to manufacturer’s information on unit or installation instructions for required subcooling 

and approach temperatures.)

Subcooling:

A - B = Subcooling

Saturated Condensing Temperature (A)

minus Outdoor Air Temperature (B)

Approach:

A - B = Approach

Liquid Line Temperature (A)

minus Outdoor Air Temperature (B)

Indoor Coil Temerpature Drop (18 to 22°F):

A - B = Coil Temp Drop

Return Air Temperature (A)

minus Supply Air Temperature (B)

Summary of Contents for GE NS23AMA

























Reviews: