background image

– 2 –

GE Appliances, a Haier Company

Copyright © 2019

All rights reserved. This service guide may not be 

reproduced in whole or in part in any form without written 

permission from GE Appliances, a Haier Company.

For Warranty Information: 

1.  Go to http://products.geappliances.com

2.  Search the model number.
3.  Click on the Literature tab.

4.  Click on Use and Care Manual.

5.  Locate the Warranty page.

Warranty

Safety Information

IMPORTANT SAFETY NOTICE

The information in this service guide is intended for use by 

individuals possessing adequate backgrounds of electrical, 

electronic, and mechanical experience. Any attempt to repair a 

major appliance may result in personal injury and property  

damage. The manufacturer or seller cannot be responsible for the 

interpretation of this information, nor can it assume any liability in 

connection with its use.

WARNING

To avoid personal injury, disconnect power before servicing 

this product. If electrical power is required for diagnosis or test  

purposes, disconnect the power immediately after performing the 

necessary checks.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to 

complete a path to ground are removed for service, they must be 

returned to their original position and properly fastened.

Summary of Contents for GE APPLIANCES AZ45E07DABW5




























































Reviews: