background image

5

Maintenance

 Attention

•  Repair can only be performed by professional personnel.

•  Before touching the connection line, all power supplies should be switched off. Only after switching off the power 

supply can the operator clean the air conditioner as to avoid electric shock or injury.

•  When cleaning the air cleaner, make sure to use a stable platform; don't flush the air conditioner with water, or the 

electric shock might be caused.

Daily Maintenance:

•  Cleaning

Clean the air cleaner with the dust collector or water to remove dusts.

For too much dust, use the fan or directly spray the special cookware detergent on the air inlet grid, and then clean it 

with water after 10 minutes.

(A) remove dust with dust collector.

(B) for too much dust, use soft-hair brush and mild detergent to clean. 

(C) throw off water and then dry it at cool places.

•  Don't clean it with hot water of over 50°C to avoid fading or distortion.

•  Don't dry it on the fire, or the cleaner might cause fire.

 Attention

Clean the air cleaner &Inlet guide plate

Clean the air cleaner 

•  Don't dismantle the air cleaner if not cleaning,  orfaultsmight be caused.

•  When the air conditioner operates in the environment with too much dust, clean the air conditioner more times 

(generallyonce every two weeks).

As shown in the drawing, draw the wind guide on both sides of the rack, with the thumb to hold downthe screen two 

buttons down gently pull the other side of the filter from the bayonet can be removed.

opposite fastener

fastener

Rack

Summary of Contents for AB052MAERA

























Reviews: