background image

3. If the fuse of indoor unit on PC board is
   broken,please change it with the type of
   T. 3.15A/ 250V. If the fuse of outdoor
  unit is broken,change it with the type of
   T.25A/250V

     Do not obstruct or cover the ventilation
grille of the air conditoner.Do not put fingers
or any other things into the inlet/outlet and
swing louver.

     Do not allow children to play with the air
 conditioner.In no case should children be
allowed to sit on the outdoor unit.

 The refrigerating circuit is leak-proof.

1.Applicable ambient temperature range:

Cooling

Indoor

Maximum:D.B/W.B 32

o

C/23

o

C

24

o

C/18

o

C

-7

o

C/-8

o

C

46

o

C/26

o

C

18

o

C

27

o

C

15

o

C

18

o

C/14

o

C

Maximum:D.B/W.B
Minimum:D.B

Maximum:D.B
Minimum:D.B

Minimum:D.B/W.B

Maximum:D.B/W.B

Minimum:D.B/W.B

Outdoor

Indoor

Outdoor

Heating

 Specifications

The machine is adaptive in following
situation

2. If the power supply cord is damaged, it
   must be replaced by the manufacturer
   or its service agent or a similar qualified
   person.

4. The wiring method should be in line with
   the local wiring standard.

5. After installation, the power plug should
   be easily reached.

6. The waste battery should be disposed
   properly.

2

10 .The power plug and connecting cable
      must have acquired the local attestation.

7. The appliance is not intended for use
    by young children or infirm persons
    without supervision.

8. Young children should be supervised
    to ensure that they do not play with
    the applience.

9.Please employ the proper power plug,
   which fit into the power supply cord.

11.In order to protect the units,please turn
     off the A/C first, and at least 30 seconds
     later, cutting off the power.

Cautions

Summary of Contents for 2HUM14H03/R2(DB)
































Reviews: