3
www.hager.com
6E 6101C
6E
61
01
C
OFF
EG010
§
1 channel time switch - daily cycle User instruction
Function
The EG010 is a programmable time switch for
the automatic control of electrical loads.
The clock contains 5 pre-programmed (user
adjustable) time periods, based on one, two or
three switchings per day.
The front cover is sealable preventing
unauthorised access after completion of
programming.
Presentation :
Display :
time
output contact (ON or OFF)
program selected
Buttons :
“
P
” to select the program to apply
to scroll program steps
“
reset
”
“
+
” and “
-
” : change settings
Time setting
Press key “
+
” or “
-
”.
A continuous pressure on this key will scroll up
or down minutes and then hours.
Programming
1. select one of the programs described below.
2. modify switching time, if necessary.
3. the program selected will be applied on a daily
basis.
To modify a program
1. select with key “
P
” the program to modify.
2. scroll program steps with the key
.
3. modify the switching time with keys “
+
” or “
-
”.
4. press key
, to display the next program
step and modify it, if necessary.
5. press “
P
” to confirm all modifications are complete
and switch back to automatic mode.
6. a small mark (*) appears next to the program
number, to indicate that the program has been
modified.
To override the circuit ON or OFF
Press “
P
” and select P0 to override the circuit OFF.
Press “
P
” and select P1 to override the circuit ON.
To switch back to automatic mode, press key “
P
”
and select the program applied previously (P2, P3
or P4).
For example :
Control an electrical equipment with program P3.
1. press key “
P
”
until «P3» is displayed.
2. if the pre-programmed switching time meets your
requirements, then programming is complete.
OFF
P
-
+
6
7
4
3
1
5
2
P0
P1
P2
P3
P4
6.00
8.00
11.00
13.00
17.00
23.00
6.00
8.00
17.00
23.00
6.00
23.00
ON
OFF
P
Prog
Example :
You have selected the program P3, but you want to
switch on the electrical equipment at 16h45 instead
of 17h00.
1. press key “
P
”
to select the program P3.
2. press
until display «17:00».
3. press “
-
”
until display «16:45».
4. press “
P
” to confirm and switch
back to automatic mode.
L
N
6
5
2
1
4
3
EG 010
1 2
3
Technical specifications
Electrical characteristics
- supply voltage 230V
쓒
+10%/-15% 50Hz/60Hz
- power consumption
= 1 VA
- output
1 changeover contact
µ 16A - 230V
쓒
AC1
µ 3A - 230V
쓒
cos
φ
= 0,6
- protection degree
IP20
- insulation class
II
- maximum operating height
2000m
- rated impulse voltage
4 kV
Functional characteristics
- accuracy
± 1sec / day at 20 °C
- operating reserve
lithium battery total of three years
- action type
1B
- degree of pollution
2
- software class
A
Environment
- operating temperature
-10 to +50 °C
- storage temperature
-10 to +60 °C
- temperature for the ball pressure Test
75° to 125°C
Connection tunnel terminals
- flexible
0.5 to 2.5 mm
2
- rigid
0.5 to 4 mm
2
Standards
60730-1
60730-2-7
Electrical connections
OFF
OFF
ON
ON
*
To check your settings
Press repeatedly key
, to display program
steps : switching time and circuit status
(ON or OFF).
To switch back to automatic mode press key
“
P
”.
To reset the time switch
Press the “
reset
” button. This will cancel all
modifications made on pre-programmed
settings.
§
Warranty
NOT APPLICABLE FOR AUSTRALIA
A warranty period of 24 months is offered on hager
products, from date of manufacture, relating to any material
of manufacturing defect. If any product is found to be
defective it must be returned via the installer and supplier
(wholesaler). The warranty is withdrawn if:
- after inspection by hager quality control dept the device is
found to have been installed in a manner which is contrary
to IEE wiring regulations and accepted practice within the
industry at the time of installation.
- The procedure for the return of goods has not been
followed. Explanation of defect must be included when
returning goods.
This device must be installed only by
a qualified electrician according to the
installation standards in force in the
country.
Usable in all Europe
å
and in Switzerland
