manualshive.com logo in svg

Häfele StealthLock 237.56.350, Mounting Instructions

Share
Download
Häfele StealthLock 237.56.350 Mounting Instructions Download Page 8

Programming Learn Disable / Learn Enable

Learn Disable / Learn Enable Mode allows the supervisor to either allow or not allow a 

user

 to program a new user code. In Learn Disable Mode, only the users with knowledge 

of the supervisor code can make any programming changes. 

There is a 60 second programming time limit to each step. If you time out or make an 

error, programming will end and you will need to restart from step 1. 

1. We suggest reading through instructions prior to beginning programming 

2. Press and hold the Receiver Latch learn button until the yellow LED begins a 

three blink

 pattern 

3. Enter the Supervisor pin code and press the 

Unlock 

button 

Then either

a. Set 

Learn Disable

, enter

3333

 and press the 

Lock 

button 

Or

b. Set 

Learn Enable

, enter

3333

 and press the 

Unlock 

button

4. If successful the green LED will flash twice on the Receiver Latch 

5. Continue programming or enter

9999

followed by pressing the Lock button to 

exit Learn Mode

6. Test lock function for new mode operation. If Learn Disable has been set, the 

Receiver Latch should automatically go to a three blink pattern when the learn 

button is pushed and held. 

R

Reset Factory Default Settings

This feature returns the lock to its original factory settings. This will place the Receiver

Latch into a Non Single Use Mode, Passage Mode, and Learn Enable Mode.  It does not

reset the user or supervisor code. 

There is a 60 second programming time limit to each step. If you time out or make an 

error, programming will end and you will need to restart from step 1. 

1. We suggest reading through instructions prior to beginning programming 

2. Press and hold the Receiver Latch learn button until the yellow LED begins a 

three blink

 pattern 

3. Enter the Supervisor pin code and press the 

Unlock

button 

4. Enter

4444

 and press the 

Lock

button 

5. If successful the green LED will flash twice on the Receiver Latch.

Note that if  Single Use mode was exited, the user pin code will default to 

0000

6. Continue programming or enter

9999

followed by pressing the 

Lock

 

button to exit Learn Mode 

7. Test lock function to make sure default settings are restored 

8

Summary of Contents for StealthLock 237.56.350











Reviews:

No comments

Brands by name

Popular brands

Load more brands