Haes ESEN-2MAR Installation, Commissioning & Operating Manual Download

Page: 8 / 44

Esento Marine 2-4 Installation, Commissioning & Operating Manual

Approved Document UI-ESEN4MAR-01 Issue 6.0

ABOUT THIS PANEL

General Specification

Enclosure

Steel IP30. Epoxy powder coated Interpon Radon, silver grey

Temperature range

-5 deg C to +55 deg C max RH 95%

Vibration

IEC 60068-2-6 Test F

Inclination

IEC 60092-501 22.5

Number of conventional detection circuits

2 or 4

Detector compatibility

Apollo: S65, Orbis. / Hochiki CDX. / Nittan EV

TECHNICAL SPECIFICATION

Electrical Specification Inputs & Outputs - TPCA01-H2/H4

Cabling

Fire resistant screened cable, minimum
size 1mm

. Max cable length 1Km (20

Ohm). FireBurn, FP200 or equivalent
(max capacitance 1uF, max inductance 1
millihenry).

Suitable cable glands must be used.

Terminal capacity

0.5mm

to 2.5mm

solid or stranded wire.

PSU @ output

Power supply voltage control line.

For temperature compensation control.

PSU Input + -

28vdc supply input. Diode protected for

reversal and independent short circuit.

Max current 3 amps.

Max input current 3 amps. Input voltage
22vdc to 32vdc.

28v+, 0v- power output

28vdc supply output for fire alarm
accessory relays etc. Max continuous
use = 400mA.

Fused @ 500mA. Fuse = 500mA

resettable fuse.

Common fire relay

Fire relay contact. Clean C/O.
Max 3A @ 30vdc

Unfused

Common fault relay

Maintained fault relay contact. Clean
C/O. Max 3A @ 30vdc

Unfused

Outputs; FR, FLT

Switched -ve voltage outputs for relay

control.

Overload voltage protected to 52vdc.
Current limited 680R. Max load = 40mA

Inputs; CC, PUL

Switched -ve inputs, connect to 0v to
trigger. Max input voltage = 28vdc. Non
latching, max resistance 100R.

Protected via 10K Ohm impedance, 3v6

zener diode.

SNDR 1 - 2

28vdc polarity reversal monitored
sounder outputs to fire alarm devices.
4K7 Ohm 5% 0.25W EOL resistor.

Monitoring current limit 28mA, fused @
500mA. Typical max load 22 devices @
18mA each per circuit. Ensure 0.9A is not

exceeded.

Zone 1 - 4

Fire alarm zone circuits. Conventionally
wired detection circuit. 4K7 Ohm 5%
0.25W EOL resistor.

Maximum detector load 3.5mA per zone,
Typical qty 40-50 Apollo marine optical
detectors, Note:- Max 32 detectors with
line continuity diode bases fitted

Summary of Contents for ESEN-2MAR













































Search results

Summary of Contents for ESEN-2MAR

Reviews:

Related manuals for ESEN-2MAR

Brands by name

Popular brands

Haes ESEN-2MAR, Installation, Commissioning & Operating Manual

Search results

Summary of Contents for ESEN-2MAR

Reviews:

Related manuals for ESEN-2MAR

Brands by name

Popular brands