background image

Figure 7  Wiring example

1   

PLC

3   

SC4500 controller

2   

Industrial switch

4   

Laptop

Section 4 Startup

1.

Supply power to the controller and PLC.

2.

Set the PLC to on.

Section 5 Operation

5.1 Configure the Ethernet ports

Make sure that the Ethernet port configuration in the controller is set to one of the IEP (industrial
Ethernet ports) options.

1.

Push the main menu icon, then select 

Controller

 > 

Connectivity

 > 

LAN

 > 

Ethernet ports

.

2.

Select one of the options that follow based on the wiring configuration of the controller.

Option

Description

IEP only

The two Ethernet ports are configured for PROFINET or EtherNet/IP. Port 2 in the
module is enabled. Refer to 

Figure 6

 on page 7.

MIX IEP

One Ethernet port is configured for LAN connectivity and the other Ethernet port is
configured for PROFINET or EtherNet/IP. Port 2 in the module is disabled. Refer to 

Figure 5

 on page 6.

Note: When Mix IEP is selected, LAN port configuration shows in the LAN menu. LAN port
configuration
 setting is used only for LAN connectivity configuration, not for Industrial Ethernet
port configuration.

8

   

English

Summary of Contents for SC4500

















































Reviews: