background image

15 

 

Heating

 

 

Dust emission limitation

 

 

By proper use dust emission can be greatly 
avoided. Factors affecting the dust and soot 
by the VDI guideline 2118 are set forth in the 
table below. 

Soot and dust formation are enhanced 
by:

 

 

High content of slack in fuel 

 

Damp fuel 

 

Inappropriate fuel 

 

Strong flames / moving the grill 

 

To small delivery pressure 

 

Chimney cooling down too fast 

Building of soot and dust are reduced 
by:

 

 

Use coal without slack, dry and suitable fuels 

 

Shake off just before charging the fuel 

 

Correct dimensioning of the chimney cross-
section 

 

Tight chimney and exhaust gas pipes 

 

Thermal insulation of the chimney 

 
Heating mode

 

 

To light up place the igniting material 
(wood logs, fire wood, fire lighter cubes, 
wood wool) on the clean grid. The 
regulation of the combustion air is 
supplied via the air control on the front of 
the stove. During heating up the controller 
is set to „Start“.  The ignition valve opens 
automatically in "Start" position by an 
operation wire. After the heating up 
phase, the knob must be set to the 
respective fuel. As soon as the small 
amount of fuel is well burnt through 
additional combustible can be added.. 

Heating door has to be closed during 
heating! 

 

 

 

Heating with wood

 

 

Firewood may be burned only air-dried. 

 

For heating adjust the air regulation to 
"wood".  
Combustion rate depends on the local draft 
conditions so that the position of the air 
regulator’s knob. 

 

 

Heating with coal

 

 

When heating with coal, particularly pay 
attention to adjustment of air regulation, 
since with too much air there is a risk of 
overheating. Fill the stove at least in two 
installments with about 15 mins intervals. 

 

Heating with brown coal at nominal heat 
output: Put the air regulator to position 
‘endurance burning‘. The firing time depends 
on the fuel volumes. 

 

Heating with brown coal at partial-load 
operation: Put the air regulator to position 
‘partial-load operation‘. However use this 
mode only when the combustibles had fully 
ignited till the top. 

 

 

 

The burning rate depends on the local draft 
conditions and the position of the air 
regulators.

Summary of Contents for HSDZ 75.5-SF easy

























Reviews: