background image

 

 

The M9010 has two cable management brackets—the signal cable management brackets are 

installed at the upper part of the gateway, and the power cable management brackets are installed 
at the lower part of the gateway. They are installed in the same way. For more information, 

see 

Figure 3

 

The power cable management bracket installation procedure for the M9014 is the same as M9010.  

 

The power cable management brackets of the M9006 have a slightly different structure, and 
installed in a similar procedure. For more information, see 

Figure 4

To install a cable management bracket: 

1.

 

Unpack the cable management brackets. 

2.

 

Attach the cable management bracket to the chassis, and align the screws with the mounting holes 
on the chassis, as shown in 

Figure 3

3.

 

Fasten the screws. 

Figure 3

 

Attaching cable management brackets to an M9010 

 

(1) Attach the cable management bracket to the chassis
(2) Screw holes for installing the cable management bracket 
(3) Screws for attaching the cable management bracket to the chassis
(4) Signal cable management bracket (installed at the upper part of the chassis)
(5) Power cable management bracket (installed at the lower part of the chassis) 

 

1

2

3

4

1

2

3

5

Summary of Contents for SecPath M9000 Series
















Reviews: