background image

<Sysname> display mad 

MAD LACP enabled. 

MAD BFD disabled. 

MAD ARP disabled. 

# Display detailed MAD information. 

<Sysname> display mad verbose 

Current MAD status: Detect 

Excluded ports(configurable): 

  GigabitEthernet 2/1/0/2 

  GigabitEthernet 2/1/0/3 

Excluded ports(can not be configured): 

  Ten-GigabitEthernet1/2/0/25 

  Ten-GigabitEthernet2/2/0/26 

MAD enabled aggregation port: 

  Bridge-Aggregation2 

MAD BFD enabled interface: 

  Vlan-interface10 

    mad ip address 10.0.0.2 255.255.0.0 member 1 

    mad ip address 10.0.0.3 255.255.0.0 member 2 

Table 5

 

Command output 

Field Description 

Current MAD status 

Status of MAD detection: 

 

Detect

—The IRF fabric is integrated.  

 

Recovery

—The IRF fabric is in Recovery state. When detecting a 

multi-active collision, MAD places the IRF fabric with higher master ID 

in Recovery state. MAD also shuts down all physical ports in the fabric 
except IRF physical ports and ports that are configured to not shut 

down. 

 

Detect to Recovery

—The state of the IRF fabric is changing from Detect 

to Recovery, for example, as the result of an IRF split. 

 

Recovery to Detect

—The state of the IRF fabric is changing from 

Recovery to Detect when the failed IRF link is recovered.  

Excluded ports (configurable) 

Ports manually configured to not shut down when the IRF fabric transits to 
the Recovery state.  

Excluded ports (can not be 
configured) 

Ports set by default to not shut down when the IRF fabric transits to the 
Recovery state.  

MAD enabled aggregation port 

Aggregate interface where LACP MAD is enabled.  

 

display restricted port 

Syntax 

display restricted port 

[

 chassis

 

chassis-number

 [ 

slot

 

slot-number 

] ] [ 

|

 { 

begin

 | 

exclude

 | 

include

 } 

regular-expression

 ]

 

View 

Any view 

Summary of Contents for S9500E Series







































Reviews: