background image

Installation Manual 
H3C S7500 Series Ethernet Switches 

Table of Contents

 

Table of Contents 

Chapter 6 Hardware Maintenance................................................................................................ 6-1

 

6.1 Required Tools................................................................................................................... 6-1

 

6.2 Removing and Installing a Power Module ......................................................................... 6-1

 

6.2.1 Installing a Power Module ....................................................................................... 6-2

 

6.2.2 Removing a Power Module ..................................................................................... 6-2

 

6.3 Removing and Installing Boards ........................................................................................ 6-3

 

6.3.1 Installing a Board .................................................................................................... 6-3

 

6.3.2 Removing a Board .................................................................................................. 6-4

 

6.4 Removing and Installing a Fan Tray .................................................................................. 6-4

 

6.4.1 Replacing the Fan Tray of the S7506 ..................................................................... 6-5

 

6.4.2 Replacing the Fan Tray of the S7503 or S7506R ................................................... 6-6

 

6.5 Removing and Installing the Power Distribution Box......................................................... 6-7

 

6.5.1 Installing the Power Distribution Box ...................................................................... 6-8

 

6.5.2 Removing the Power Distribution Box .................................................................... 6-8

 

6.6 Installing the Mounting Brackets and Cable Management Bracket................................... 6-9

 

6.7 Replacing a Memory Module ............................................................................................. 6-9

 

6.7.1 Upgrade Description ............................................................................................... 6-9

 

6.7.2 Structure of a Memory Module.............................................................................. 6-10

 

6.7.3 Position of a Memory Module on a Board............................................................. 6-10

 

6.7.4 Installing and Removing a Memory Module.......................................................... 6-11

 

6.8 Replacing and Cleaning the Air Filter .............................................................................. 6-11

 

6.8.1 Removing and Installing the Air Filter ................................................................... 6-11

 

6.8.2 Cleaning the Air Filter............................................................................................ 6-12

 

 

Summary of Contents for S7500 Series














Reviews: