manualshive.com logo in svg

H3C S7500E-XS Series, Installation Manual, Page: 46 / 64

Share
Download
H3C S7500E-XS Series Installation Manual Download Page 46

 

39 

Appendix A Chassis views and technical 
specifications 

Chassis views 

S7502E-XS 

Figure 47

 

Front panel 

 

(1) Interface card slot 1 

(2) Interface card slot 2 

 

Figure 48

 

Rear panel 

 

(1) USB mini console port 

(2) USB port 

(3) Fan tray slot 1 

(4) Fan tray slot 2 

(5) Power module slot 1 

(6) Power module slot 2 

(7) QSFP+ port 

(8) QSFP+ port LED 

(9) System status LED (SYS) 

(10) LINK/ACT LED for the management Ethernet port 

(11) Management Ethernet port 

(12) Serial console port 

 

The S7502E-XS switch comes with interface card slot 1 empty and interface card 2 installed with a filler 

panel. You can install one or two interface cards for the switch as needed. In 

Figure 47

, two 

LSQM1QGS8A0 interface cards are installed in the interface card slots. For more information about 

installing and removing interface cards, see "

Installing/Removing an interface card

." 

The S7502E-XS switch comes with the two power modules empty and a filler panel as an accessory. You 

can install one or two power modules for the switch as needed. In 

Figure 48

, two LSVM1AC650 power 

modules are installed in the power module slots. For more information about installing and removing 

power modules, "

Installing/removing a power module

." 

Summary of Contents for S7500E-XS Series

































































Reviews:

No comments