manualshive.com logo in svg

H3C S6520X-HI Series, Troubleshooting Manual, Page: 50 / 50

Share
Download
H3C S6520X-HI Series Troubleshooting Manual Download Page 50

47 

Troubleshooting flowchart 

Figure 23 VXLAN configuration failure 

 

 

Solution 

To resolve the issue: 

1. 

Verify that the operating mode of the switch (configured by using 

switch-mode

) is VXLAN. 

a. 

Display operating mode information. 

<Sysname> display switch-mode status 

     Switch-mode in use: NORMAL MODE(default). 

     Switch-mode for next reboot: NORMAL MODE(default) 

b. 

If the switch-mode is not VXLAN, set it to 1, save the configuration, and reboot the switch. 

<Sysname> system-view 

[Sysname] switch-mode ? 

  0  NORMAL MODE(default) 

  1  VXLAN MODE 

  2  802.1BR MODE 

[Sysname] switch-mode 1 

Reboot device to make the configuration take effect. 

[Sysname] quit 

<Sysname> reboot 

Start to check configuration with next startup configuration file, please wait.. 

.......DONE! 

Current configuration may be lost after the reboot, save current configuration?  

[Y/N]:y 

This command will reboot the device. Continue? [Y/N]:y 

c. 

Verify the switch-mode configuration after the switch finishes startup. 

<Sysname> display switch-mode status 

     Switch-mode in use: VXLAN MODE. 

     Switch-mode for next reboot: VXLAN MODE. 

2. 

If the issue persists, contact H3C Support. 

 

Summary of Contents for S6520X-HI Series



















































Reviews:

No comments