background image

About This Manual 

Organization 

H3C LSW1FAN and LSW1BFAN Installation Manual 

is organized as follows:

 

Chapter 

Contents 

1 Fan Tray Overview 

Describes the

 

fan tray and hardware specifications. 

2 Removing/Installing a Fan Tray 

Describes removal and installation of the fan tray. 

Appendix 

Appendix A: Obtaining Support for your Product. 

 

Conventions 

The manual uses the following conventions:  

Convention 

Description 

 

Means reader be extremely careful. Improper operation may cause 
bodily injury.  

 

Means reader be careful. Improper operation may cause data loss or 
damage to equipment.  

 

Means a complementary description.  

 

Obtaining Documentation and Techn

ic

al Support 

To obtain up-to-date documentation and technical support, go to 

http://www.h3c.com

 and select your 

country or region. Depending on your selection, you will be redirected to either of the following websites:  

At http://www.h3c.com 

Documentation 

Go to the following columns for different categories of product documentation: 

[Products & Solutions]: Provides information about products and technologies, as well as solutions.

 

 

[Technical Support & Document > Technical Documents]: Provides several categories of product 
documentation, such as installation, configuration, and maintenance. 

 

[Technical Support & Document > Software Download]: Provides the documentation released with the 
software version. 

Techn

ic

al Support 

[email protected] 

http://www.h3c.com 

At http://www.h3cnetworks.com 

Documentation 

Select 

Drivers & Downloads

 in the 

Support

 area. 

Summary of Contents for S5800-60C-PWR

















Reviews: