manualshive.com logo in svg

H3C MSR 20 Series, Installation Manual, Page: 65 / 77

Share
Download
H3C MSR 20 Series Installation Manual Download Page 65

 

58 

Hardware Maintenance 

Preparing Tools 

•

 

Phillips screwdriver 

•

 

Straight screwdriver 

•

 

ESD-preventive twist strap 

•

 

Static shielding bag 

 

 

NOTE: 

The tools are not available with the MSR 20. You must prepare one yourself. 

 

Opening/Closing Chassis Cover 

Step1

 

Power off the router and remove the power cord. 

Step2

 

Remove all cables of interface modules on the back panel (keep the ground cable connected). 

Step3

 

Put the router on level ground and have the back panel face you. Loosen the captive screws fastening the 
back panel with Phillips screwdriver.  

Step4

 

Put two straight screwdrivers into the holes on the two sides of the chassis and turn them until the tab on 

the front edge is separated from the front panel. 

Step5

 

Drag the chassis levelly a little towards your body and lift it, and then you can remove the cover and put 

it away. 

Figure 38

 

Remove/install captive screws of MSR 20-20/20-21 

 

 

 

Summary of Contents for MSR 20 Series














































































Reviews:

No comments