H3C H3C S7500E-X Configuration Examples Download Page 12

 

10 

Loadsharing Type: Shar 

System ID: 0x8000, 00a0-fc00-5800 

Local: 

  Port             Status  Priority Oper-Key  Flag 

-------------------------------------------------------------------------------- 

  XGE1/1/0/9         S       32768    1         {ACDEF} 

  XGE1/1/0/10        S       32768    1         {ACDEF} 

  XGE2/1/0/9         S       32768    1         {ACDEF} 

  XGE2/1/0/10        s       32768    1         {ACDEF} 

Remote: 

  Actor            Partner Priority Oper-Key  SystemID               Flag 

-------------------------------------------------------------------------------- 

  XGE1/1/0/9         139     32768    1         0x8000, 0cda-414a-859b {ACDEF} 

  XGE1/1/0/10        205     32768    1         0x8000, 0cda-414a-859b {ACDEF} 

  XGE2/1/0/9         204     32768    1         0x8000, 0cda-414a-859b {ACDEF} 

  XGE2/1/0/10        138     32768    1         0x8000, 0cda-414a-859b {ACDEF} 

The output shows that the local member ports and the corresponding peer member ports are all Selected. 

In the dynamic link aggregation mode, each local member port and its peer member port have the same 
Selected state through exchanging LACPDUs. The user data traffic can be forwarded correctly. 
# Display the load sharing mode of Layer 2 aggregation group 1 on Device A. 

[DeviceA] display link-aggregation load-sharing mode interface Bridge-Aggregation 1 

Bridge-Aggregation1 Load-Sharing Mode: 

source-ip address 

The output shows that Layer 2 aggregation group 1 load shares packets based on source IP addresses. 
# Shut down physical IRF port Ten-GigabitEthernet 2/0/1 on Device B. 
A log message appears on Device A. 

[DeviceA]%Jan  1 03:12:43:397 2011 Transit STM/3/STM_LINK_STATUS_DOWN: IRF port 2 is down. 

%Jan  1 03:12:43:410 2011 Transit DEV/3/BOARD_REMOVED: Board is removed from Slo 

t 1, type is MAIN_BOARD_TYPE_52QF. 

%Jan  1 03:12:44:385 2011 Transit IFNET/3/PHY_UPDOWN: Ten-GigabitEthernet2/1/0/1  

link status is down. 

%Jan  1 03:12:44:386 2011 Transit IFNET/5/LINK_UPDOWN: Line protocol on the inte 

rface Ten-GigabitEthernet2/1/0/1 is down. 

The output shows that IRF split occurs on the distribution layer because Ten-GigabitEthernet 2/1/0/1 

that is bound to IRF port 2 is physically down. 

Configuration files 

 

Device A: 

 irf domain 1 

 irf mac-address persistent timer 

 irf auto-update enable 

 irf link-delay 0 

 irf member 1 priority 1 

 irf member 2 priority 1 

Summary of Contents for H3C S7500E-X

















Reviews: