H3C H3C S7500E-X Configuration Examples Download Page 11

 

[DeviceA] interface range ten-gigabitethernet 1/1/0/9 to ten-gigabitethernet 

1/1/0/10 

ten-gigabitethernet 2/1/0/9 to ten-gigabitethernet 2/1/0/10 

[DeviceA-if-range] port link-aggregation group 1 

[DeviceA-if-range] quit 

[DeviceA] 

4.

 

Configure LACP MAD on the IRF fabric: 
# Set the domain ID of the IRF fabric to 1. 

[DeviceA] irf domain 1 

# Enable LACP MAD on Bridge-Aggregation 1. 

[DeviceA] interface Bridge-Aggregation 1 

[DeviceA-Bridge-Aggregation1] mad enable 

You need to assign a domain ID (range: 0-4294967295) 

[Current domain is: 1]: 

The assigned domain ID is: 1 

MAD LACP only enable on dynamic aggregation interface. 

5.

 

Configure IRF on Device C in the same way IRF is configured on Device A. (Details not shown.) 

6.

 

Configure IRF on Device D in the same way IRF is configured on Device B. (Details not shown.) 
Device C and Device D perform master election, and the one that has lost the election reboots to 
form an IRF fabric with the master. In this example, Device C reboots. 

7.

 

Configure a Layer 2 dynamic aggregation group Bridge-Aggregation 1 on Device C in the same 

way Bridge-Aggregation 1 is configured on Device A. (Details not shown.) 

8.

 

Configure LACP MAD on the IRF fabric: 
# Set the domain ID of the IRF fabric to 2. 

<DeviceC> system-view 

[DeviceC] irf domain 2 

# Enable LACP MAD on Bridge-Aggregation 1. 

[DeviceC] interface Bridge-Aggregation 1 

[DeviceC-Bridge-Aggregation1] mad enable 

You need to assign a domain ID (range: 0-4294967295) 

[Current domain is: 2]: 

The assigned domain ID is: 2 

MAD LACP only enable on dynamic aggregation interface. 

Verifying the configuration 

# Display the information about the link aggregation groups on Device A. 

[DeviceA] display link-aggregation verbose 

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing 

Port Status: S -- Selected, U -- Unselected, I -- Individual 

Flags:  A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation, 

        D -- Synchronization, E -- Collecting, F -- Distributing, 

        G -- Defaulted, H -- Expired 

 

Aggregate Interface: Bridge-Aggregation1 

Aggregation Mode: Dynamic 

Summary of Contents for H3C S7500E-X

















Reviews: