H3C DSIC-9FSW Manual Download Page 163 | Manualshive

Page: 163 / 219

background image

154

Table 209 LED description

LED Description

ESMx

•

Green: ANDE module is in the slot and is operating normally.

•

Yellow: ANDE module is in the slot but cannot be accessed by the router.

NOTE:

"x" means the number of the slot the ESM LED is in.

Installing and removing an ESM-ANDE module

For more information about installing and removing an ESM-ANDE module, see the installation
guides for the H3C MSR router models.

ESM-SNDE

Introduction

The standard network data encryption engine (SNDE) supports IPsec and hardware expedited IP
data packet encryption, thus providing encryption with high performance and reliability.

Installed with an ESM-SNDE module, the main board of your router can implement VPN with
encryption provided by the ESM-SNDE module in addition to IP packet forwarding.

Interface specifications

Table 210 Interface specifications

Item Description

Protocol supported

IPsec

Hardware algorithm

key algorithm (DES, 3DES, AES, QC5, Blowfish, Cast-128 and SkipJack)
Authentication algorithm (HMAC-MD5-96, HMAC-SHA-1-96)

Interface LEDs

There is no LED on the ESM-SNDE module. Display of the status of the module is implemented
through the ESM interface LED on the main board of the router.

The following table describes the LEDs on the SNDE panel.

Table 211 LED description

LED Description

ESMx

•

Green: SNDE module is in the slot and is operating normally.

•

Yellow: SNDE module is in the slot but cannot be accessed by the router.

NOTE:

"x" means the number of the slot the ESM LED is in.

«
...
161
162
163
164
165
...
»

Summary of Contents for DSIC-9FSW




























































































































































































































Reviews:

No comments

Related manuals for DSIC-9FSW

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

Brand: Vanderbilt Pages: 2

Brand: Daikin Pages: 46

Brand: Daikin Pages: 26

ArtNet-DMX Mux16

Brand: DMX4ALL Pages: 21

Brand: DAQ Pages: 63

Brand: Apex Toys Pages: 7

Brand: Elotech Pages: 20

Brand: Intermatic Pages: 2

Brand: Alde Pages: 36

YQPV-HP360V/100A

Brand: PSC Solar Pages: 22

Brand: Ros Pages: 10

Brand: Comparato Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands