background image

SECTI

O

2

: I

NSTA

L

L

AT

IO

N

 

18 

H2O BOILER

 HC SERIES IOM Manual 

instruments (main gas valve, boiler/water heater gas regulator, and low gas pressure switch) could 
be easily isolated and removed, whenever necessary.  The valve should be clearly marked, located 
outside the unit’s housing, readily visible and accessible for turning on and off.  If the unit is to be 
installed in, under, or directly attached to a pool, or spa, structure, the said manual valve should be 
located outside the structure. 

2.9

 

 Electrical connection 

If an external electrical source is utilized, the appliance, when installed, must be electrically 
grounded in accordance with local codes or, in the absence of local codes, with the 

National

 

Electrical Code

, ANSI/NFPA 70 and/or the CSA C22.1, 

Canadian Electrical Code, Part 1

2.10

 

 Vent Connection 

For US and Canadian installations, vent termination must be in accordance and not less than those 
specified in the current ANSI Z223.1/NFPA 54 

National Fuel Gas Code 

or CSA B149.1, 

Natural 

Gas and Propane Installation Codes

, as applicable. 

Provisions for adequate combustion and ventilation air in accordance with one of the following: 

The 

National Fuel Gas Code, ANSI Z223.1/NFPA 54 

(Current Edition);

CSA B149.1, Natural Gas and Propane Installation Code 

(Current Edition); or

Applicable provisions of the local building code.

NOTE:

 

Inlet gas pressure upstream of the unit must always remain within the 7” – 14” WC 
range. The maximum inlet gas pressure must not exceed the value specified by the 
manufacturer  and  that  the  minimum  value  listed  is  for  the  purposes  of  input 
adjustment. 

Warning: 

Use of cellular core PVC (ASTM F891), cellular core CPVC, or   Radel® 
(polyphenylsulfone) in non-metallic venting systems is prohibited. 
Covering non-metallic vent pipe and fittings with thermal  insulation is prohibited. 

CAUTION:

 

Label all wires prior to disconnection when servicing controls. Wiring errors can  
cause improper and dangerous operation. Verify proper operation after servicing. 

D-VAC Sales Inc.        Email: [email protected]        Tel: (516) 256-3131        www.dvachvac.com

Summary of Contents for HC 1000



















































Reviews: