H-KING Savage Bobber 1000 mm 5ch ARF Version Instruction Manual Download Page 17

At this point, reinforce the joint in the seam 

between the stabilizer and the tail structure by

running in a thin layer of medium CA glue.

The empennage and the landing gear setup is 

now complete.

MODEL FLYING PRECAUTIONS:

YOUR NIGHT TUNDRA COMES WITH SEVERAL FEATURES

PRE-FLIGHT CHECKS:

Always range check your model before any flight (especially when flying a new model for the first

time). Follow your radio manufacturers guidelines for performing  this check.

Check  all  screw bolts  and  mounting  points  are  firmly  secure,  including  control  horns  and

clevises.

Only fly with fully charged batteries (both in your radio and model). Failure to do so could result

in  loss  of  control,  damage  to  the  model  and/or  persons/property  around  you.  Check  your

batteries are fully charged.

With the model powered up ( ransmitter on first, then receiver/model) check that all surfaces are

free from damage/obstructions, moving in the correct directions and freely with stick input .

Inspect the model and prop for any damage that may have occurred during transit and listen for

any unusual sounds from the electronics when powered up. If in doubt, do not fly.

With the model held securely and the prop free of obstructions, increase the throttle just slightly

to confirm the rotation of the prop is correct. The model should want to pull straight forward with

throttle.

If this is your first flight with the model double check the C/G is at the correct  position. If not adjust

battery position inside model accordingly.

If you are an inexperienced model pilot seek the help and assistance of an experienced pilot to

perform these final checks and to test fly the model for you.

15

• Select your flying area carefully. Always choose an open space that is clear and not obstructed by

trees, poles, pylons, and buildings etc. Also ensure you are away from people and crowded areas.

Avoid flying in areas with roads, near water, or within close proximity to full size air traffic.
• Do not fly this model in poor weather, for example: high winds, low visibility, inclement temperatures,

and rain and storms are also to be avoided.
• Never attempt to catch the model whilst it is in flight, even a slow moving model can cause harm to

yourself and risks damage to the model.
• This model is not recommended for children under the age of 14 years old. All children no matter

what age, should be supervised by a capable and responsible adult when operating this model.
• Always unplug your model battery when not in use, never leave the battery installed in the model.
• Please remember to keep clear of the propellers at all times when your flight battery is connected.
• Before flying, always turn ON your transmitter first, then plug your flight battery into the model.
• After flying, always unplug your battery first in the model and then turn OFF your transmitter.
• Exercise caution when charging your batteries, and follow in full your battery manufacturers safety

guideline when doing so.

Summary of Contents for Savage Bobber 1000 mm 5ch ARF Version




















Reviews: