background image

4

 

Technical parameters 

Measured and calculated values 

Temperature: 

Measuring range: 

-10 to +60 

°C, internal sensor (INT)

-30 to +105 

°C, external sensor (EXT)

Resolution: 

0.

1 °C 

Accuracy:  

±0.4 °C 

Response time (EXT):  t90 < 3 min with plastic sensor cover without filter 

t90 < 8,5 min with plastic sensor cover with stainless filter 

_____________________________________________________________________________________________________________________ 

Air flow approximately 1m/s, temperature step 20 

°

Relative humidity: 

Measuring range: 

0 to 100 %RH 

Resolution: 

0.1 %RH 

Accuracy: 

± 2.5 %RH from 5 to 95 %RH at 23 ºC  

Response time:  

t90 < 1 min with plastic sensor cover without filter 
t90 < 1 min with plastic sensor cover with stainless filter 

_____________________________________________________________________________________________________________________ 

Air flow approximately 1m/s, humidity step 30 %RH, constant temperature 

Atmospheric pressure: 

Measuring range: 

800 to 1100 hPa 

Resolution: 

0.1 hPa 

Accuracy: 

± 2 hPa at ambient temperature of 23 ºC 

Dew point temperature:

 

Measuring range: 

-50 to 

+80 ºC

Resolution: 

0.

1 ºC

Accuracy:   

±1.5 °C at temperature T<25 °C and RH>30%
(for more details see graph)

Summary of Contents for AR006292















Reviews: