background image

Guangzhou Yingfeng Lighting Equipment Co.,Ltd

www.yf-light.com

2

1

Open-package inspection

First of all thank you for buy our products.Please read this user manual completely and carefully, and

keep it well for reference when needed. This use manual includes important information about the

installation and using of the moving head. Please hew to the relevant specification strictly when install and

use this product.

This Moving head light is made of new high strength heat-resistant engineering plastic and cast

aluminum shell , with beautiful design and smooth outlook, Is the representative of the modern lights. This

product strictly according to CE standard design and production, fully comply with international standard

DMX 512 protocol.Can be single control , also can use integrated with each other. It is suitable for

large-scale theatrical performances, theaters , studio and disco and other places.

After receiving the product, please be careful to take and put., Check if the product have been damaged

during the transportation, and check the following parts:

The body-------------------------------------1pcs

Safe rope--------------------------1pcs

Power cable ----------------------------------1pcs

hook------------------------------2pcs

User manual -------------------------------- -1psc

signal cable-----------------------1pcs

2

Attentions

1. To ensure the service life of the product, please keep it away from water and do not work in the

environment which the temperature is above sixty degrees.

2. Don’t put the product on the place easy to loose or easy vibration .

3. In order to avoid electric shock, this product must maintenance by professional person.

4. when using, the power supply voltage change should not be more than 10%, the voltage is too high, will

shorten the life of the light bulb, the voltage is too low, then affects the light color.

5. When power off, the product need 20 minutes to sufficient cooling before use again.

6. To ensure the normal use, please read this user manual carefully.

3、Technical Parameter

1.

Voltage

:AC100V-240V

2.

Frequency

:50/60Hz

3. Rated power:350W
4. Lamp:Philips
5. Bulb power:200W
6. Strobe:1-13times/second
7. Color temperature:7800K

8. Horizontal scanning 540 degrees, Horizontal 16 bit, electronic error correction, vertical scanning
270 degrees, vertical 16 bit, electronic error correction.

9. Gobo:17 gobo add white and stream effect,gobo electric focus function
10. Color:14 color add white and rainbow effect

Summary of Contents for BEAM 200










Reviews: