background image

18

Powering the System 

IMPORTANT:

 

•  The 

GTO/PRO SW 1500

 is designed and intended for use with a 12 Volt automotive or marine type 

battery. The battery must be placed inside a weatherproof case and located within 6 feet of the operator arm. 
The 10 foot harness supplied connects the battery to the operator arm.

 

•  The battery charge is maintained by the 18 Volt transformer included 

or

 by using optional solar panel(s). 

The transformer 

or

 solar panel is connected to the operator arm control board using low voltage, 16 gauge, 

dual conductor, multi-stranded, direct burial wire (FM509) (

see page 20 and the

 

Accessory Catalog

).

 

•  All low voltage wire used with the 

GTO/PRO SW 1500

 must be 16 gauge dual conductor,

 

  multi-stranded, direct burial wire (

see page 20

 and the 

Accessory Catalog

).

  Do not run more than 1000 

feet of wire.  

 

•  The transformer is designed and intended for indoor use.  If the transformer can be plugged only into an 

outside electrical outlet, a weatherproof cover or housing (available at local electrical supply stores) 

must

 

be used. 

 

•   If your gate is more than 1000 ft. from an ac power source, you will need to use at least one 5 watt Solar 

Panel to charge the battery (see

 Accessory Catalog

).  

Refer to the 

Solar Panels and Gate Activity 

chart 

below.

The table and map 
illustrate the maximum 
number of gate cycles 
to expect per day in a 
particular area when 
using from 5 to 30 watts 
of solar charging power. 
(

see Accessory Catalog

).  

The figures shown are 
for winter (minimum 

sunlight) and do not account for the use 
of any accessory items.  

Accessories connected to your system 
will draw additional power from the 
battery and will require additional solar 
panels.

NOTE

: A maximum of 30 watts of solar 

charging power can be connected to the 

GTO/PRO SW 1500

.  Consult 

Solar 

Panel

 

Installation Instructions for further 

information

.

Single Gate Winter Ratings 

   Zone 1 

Zone 2 

Zone 3

12 v single gate (5 watts) solar charger  

13

12 v single gate (10 watts) solar charger   8 

16 

26

12 v single gate (15 watts) solar charger   11 

20 

30

12 v single gate (20 watts) solar charger   14 

28 

38

12 v single gate (25 watts) solar charger   17 

36 

46

12 v single gate (30 watts) solar charger   20 

44 

54

Solar Panel and Gate Activity Chart

NEVER USE TRANSFORMER AND SOLAR PANEL(S) AT THE SAME TIME

– it willl damage the control board –

Summary of Contents for SW-1500














































Reviews: