background image

  2

Figure 4

Lens Hood

Lens

4 Watt Light

Light Socket

Lens Support

Mounting Plate

Low Voltage Wire 

(RB509)

Wire Nuts

Figure 5

Figure 1

INSTALLING THE LIGHTS

Installing lights on the face of the gate post:

1. Insert small screws into holes on the underside of lens hood as 

shown in 

Figure 1

. Only screw them part way so they can twist 

lock into place on top of lens.

2. Install wires into the light bulb socket by simply pressing a brass 

connector into each side of the socket until it snaps into place. 
See 

Figure 2

.

3. Line up the slots on the socket with the notches in the lens. Insert 

the scoket into the lens. Firmly grasp the socket, push and twist 
until it snaps into place as shown in 

Figure 3

.

4. Assemble the rest of the light using the angled lens support as 

shown in 

Figure 4

. Do not glue any of the parts at this time.

Figure 2

Figure 3

5. Determine where the low voltage wire will be run. 

Connect to the lights using the wire nuts provided 
before mounting the fi xtures. The notches in the 
mounting plates are openings for running the low 
voltage wire. Be sure it is facing the direction the 
wire will enter.

6. Use the self tapping screws provided to attach the 

assembled fi xtures to the gate posts. Additional 
hardware my be required depending on the type of 
gate posts you have. See 

Figure 5

.

7. When you are satisfi ed with the placement of the 

fi xtures, glue the lens support pieces using a small 
amount of glue (provided). Be careful to keep the 
glue off the outside of the support pieces.  See 

Fig-

ure 6

.

Figure 6

Use small 

Use small 

amount of glue 

amount of glue 

to secure lens 

to secure lens 

support as-

support as-

sembly

sembly

Summary of Contents for Digital Controlled Gate Opener Light Kit













Reviews: