WORK LIGHT CONSTRUCTION:
A.
Carrying handle with comfort grip
B.
Lightweight, scratch-resistant aluminum frame
C.
Tiltable light face
D.
LEDs
E.
Tempered glass protective lens
F.
AC Power Adapter (ETL)
G.
6ft Micro USB Cable
H.
Micro port for charging the light
I.
USB port for charging other devices
J.
On/Off Button
K.
Side star knobs (2)
L.
U-frame
M.
Base knob (1)
N.
H-stand base
O.
Textured rubber feet for strong surface grip
ASSEMBLY:
1. Attach U-Frame
(L)
to H-Stand
(N)
by screwing Base Knob
(M)
completely through the holes on
(L)+(N)
until tight.
TO USE:
1.
CHARGE THE LIGHT FOR APPROXIMATELY 8-10 HOURS
a. Insert the Micro End of the 6ft Micro Cable
(G)
into the Micro
Port
(H)
on the back of the work light.
b. Insert USB End of the 6ft Micro Cable (G) into the AC adapter
(F).
c.
This product must be charged with UL or ETL certified
adapters or warranty will be void.
d. Plug the AC Adapter (F) into Power.
2. Place H-Stand
(N)
on a sturdy surface. Ensure that all 4 Rubber Feet
(O)
have a secure grip on the surface.
3. Slightly loosen side Star Knobs
(K)
(do not unscrew completely).
4. Tilt Light Face
(C)
up or down to the desired angle.
5. Tighten Star Knobs
(K)
.
6. Slightly loosen Base Knob
(M)
(do not unscrew completely).
7. Swivel U-Frame
(L)
side to side to the desired angle.
8. Tighten Base Knob
(M)
.
9. Remove light from power if desired. Light will work while charging or if
removed from power.
10. To turn light on HIGH 4000 LM, press On/Off button
(J)
one time.
11. To turn light on LOW 2000 LM, press On/Off button
(J)
a second time.
12. To turn light off, press On/Off button
(J)
a third time.
13. To charge a device, plug device into USB port
(I)
.
a. USB port works with LED light on or off—as long as the unit is
plugged into a power outlet or the internal battery is charged.
14. Store in a cool dry place when not in use.
TROUBLESHOOTING
Problem
Cause
Solution
LED is not
lighting up.
No power or faulty
connection.
LED Light is not fully
charged.
Check that all connections are
secure, and power is ON.
Charge battery for a full 8-10
hours and try again.
Questions,
Missing Parts
Customer Service:
1-800-865-6799
CARE AND CLEANING
Your fixture is made from quality materials that will last an extended period of
time with proper care—including periodically cleaning the surface of the fixture.
1. Use a mild, non-abrasive cleaner. Do not use any solvents or harsh
cleaning agents.
2. Use a soft, non-abrasive cloth.
3. Lightly spray cleaner onto the cloth. Do not spray liquid cleaners directly
onto LEDs, power cord, or any part of this product.
4.
Lightly wipe down fixture with damp cloth. Allow product to dry completely
before restoring power and using LED lights.
NOTICE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient
or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3)
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(4) Consult the dealer or an experienced radio/TV technician for help.
A
B
C
D
E
L
K
M
N
O
H
I
J
F
G
